This Control Actuation System (CAS) is a guidance system for unmanned flying objects. It consists of three MPS fin actuators that each independently position an aerodynamic fin. The maximum angle of incidence is ±8°, which allows the device to carry out highly precise dynamic manoeuvres. The miniature fin actuators that make up this Control Actuation System are manufactured by MPS Microsystems and were designed based on customer specifications. Designed to guide a very small object and disposing of an extremely limited space, these fin actuators meet strict requirements in terms of performance, weight - less than 100 g - and dimensions. To reduce the length of this actuator, MPS Microsystems used part of the screw length as the motor axis. This screw is equipped with a very compact 4-point contact bearing that simultaneously absorbs axial and radial loads. The angular play on the aileron axis is less than 0.1° rms. This actuator meets the storage and vibration requirements of military equipment.

The A-C series is the most lightweight and low profile altitude switch in the Precision Sensors product line. The capsule based sensing element provides repeatable and precise absolute pressure threshold detection by sensing changes in the ambient air pressure compared to an evacuated capsule. The skeletal construction removes the need for bulky pressure fittings.

Typical uses include aircraft cabin air pressure monitoring.

For an environmentally sealed alternative, refer to the E-C series. For qualification information, please consult the sales or engineering departments.

Features

Intended for gaseous media
Low profile skeletal design
Ni-Span-C capsule provides superior setpoint stability over temperature
Custom configurations available upon request

The PNT500 is a rugged 3U VPX Assured Position Navigation and Timing(A-PNT) module aligned with the SOSA profile, offering multi-constellation QinetiQ Q40 GNSS, PTP Grandmaster timing, OCXO/CSAC fallback, and ruggedized reliability. • QinetiQ Q40 multi-GNSS receiver with anti-jamming/spoofing • IEEE 1588 PTP Grandmaster; OCXO or CSAC timing fallback, 1 PPS and reference outputs • Rugged single-slot 3U VPX, SOSA-aligned

- Power supply and control for the driver camera and thermal camera - Video signal selection and display: driver camera & thermal camera

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. Linear Acceleration Compensation Certus Mini uses an innovative algorithm to compensate for linear accelerations. This allows Certus Mini to maintain accurate roll and pitch through short term linear accelerations that typically cause significant errors in competitors systems. For long term linear accelerations Certus Mini supports the addition of an external GNSS receiver for full acceleration compensation. Extensive Interoperability Certus Mini seamlessly communicates with a wide range of industry standard protocols including NMEA 0183 and CANOpen making it easy to integrate into existing systems. Certus Mini effortlessly interfaces with ROS 1, ROS 2, and Ardupilot, streamlining your development processes for maximum efficiency and effectiveness.

Using a data storage module and a series of high-speed switches, our solution offers expandable memory up to 64 TB and high-speed processing power. Along with our attendant control panel, designed to reduce the crew's workload, we offer a complete end-to-end solution.

Magnetic sensors (Hall effect) for air and land applications fly by wire

The Striker II digital Helmet-Mounted Display (HMD) builds on the decades of combat-proven performance by the Striker HMD, used on Typhoon and Gripen aircraft. The only full color solution with integrated night vision available anywhere, Striker II gives pilots unparalleled situational awareness, next generation EBAPS™ night vision, optional 3D audio, and battle proven target tracking technology - all in an integrated, visor-projected digital HMD system.