STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Main Characteristics Excellent broadband characteristics Radiation patterns virtually independent of frequency Only one antenna required to cover a wide frequency range Selectable polarization plane Sturdy construction Suitable for mobile use Main Use Optimized for radiomonitoring and measurements Design Owing to its broadband characteristics and the virtually frequency-independent radiation patterns, the SLP – 200M-001G covers a very wide frequency range The sturdy construction makes the antenna Suitable for stationary and mobile applications

We developed and optimized an object detection and tracking solution tailored for edge environments using Intel Atom platforms with OpenVINO. The system combines MobileNetV3-SSDLite for detection and MobileNetV3-Small for tracking, enabling efficient real-time performance on resource-constrained devices. Through model optimization and inference acceleration, we achieved over 2x improvement in FPS and more than 50% enhancement in inference speed, all while maintaining detection and tracking accuracy. This demonstrates the solution’s suitability for lightweight, low-power edge AI applications

This fully self-contained pressure test and calibration system combines pressure generation, signal measurement, and loop power to deliver all the convenience of the Druck DPI 610/615, while being half the size, twice as accurate and easy to use. The DPI 611 is the fourth generation of the DPI 600 family, first introduced in 1984. The DPI 600 family revolutionized testing and calibration by providing all the tools for pressure generation and signal measurement in a stand-alone portable package. The DPI 600 soon became the flagship equipment of the industry and today it is simply known as "Druck". Built on a technical legacy and more than 30 years of experience in pressure measurement and calibration, the DPI 611 offers all the convenience and reliability of a true "Druck", while delivering double the performance of a product half its size.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Liquid Measurement System (LMS) capacitance AC and DC fuel gauging probes use lightweight and durable carbon composite materials. In addition to being some of the lightest fuel probes in the industry, they are also virtually immune to corrosion, cracking, dents, and extreme field conditions. Our capacitance probes are inherently crash resistance by collapsing onto itself during hard impact landings to avoid tank penetration and fuel leaks. All electrical connections on the probe are bonded, and there is no friction or riveted electrical connections.

Altimeter for Missile Application

The SDI170 IMU is designed for demanding, mission-critical, rugged environments and ideal for continuous use applications with no wear-out components, highly linear accelerometer performance and longer life compared to competing alternatives. It is constructed with EMCORE’s latest generation quartz gyros, quartz accelerometers, and high-speed signal processing to achieve outstanding precision performance. The solid-state quartz sensors and hermetically sealed IMU construction provide reliable MTBF and a 20-year operating and storage life. Continuous Built-in Test (BIT), configurable communications protocols, electromagnetic interference (EMI) protection and flexible input power compatibility make the SDI170 IMU easy to use in a wide range of higher-order integrated commercial and defense system applications.