STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

The MIL-DTL-5015 series of connectors were developed as military standard connectors and applied to various military equipment, it is also used in general industries, medical care, electric vehicles, robots and automation facilities based on its high durability and reliability. This series is threaded coupling and the connection between the contact and the wire is based on soldering. It can be used compatibly with third-party products of the same standard since it is produced according to military standards.

The FLIR 380X upgrade sets the new standard for law enforcement mission support. Learn more: https://www.flir.com/surveillance/flir-380x-upgrade/

Applied for the Localization Development Project of Core Components in Weapon Systems Conducted basic design for the development for mechanical Mine Sweeping Equipment for MSH, followed by submission of a proposal and presentation for in-person evaluation Patent : Mine Sweeping System with loT Based Functional Float

Poongsan has been producing a variety of copper and copper alloy plates, ranging from copper products for everyday life to high-tech industrial materials. These copper and copper alloy plates, which are recognized as high-quality materials at home and abroad, are representative industrial basic materials that are widely used in all industrial fields, including automobiles, electrical and electronics, semiconductors, communications, construction, and machinery. Poongsan has various casting facilities, including the world's largest shaft furnace, a hot mill capable of continuously rolling 6-ton slabs, a tandem mill, and a 20-stage cold rolling mill, as well as various hot and cold rolling facilities and heat treatment furnaces. We are building a large-scale integrated production system from the casting process to finishing processes such as cutting and packaging. Poongsan's rolled products are produced in various sizes depending on the type, ranging from 630mm in width, 0.03mm in thickness, and thickness tolerance to 2/1000mm. These products have accurate specifications and physical properties and a smooth surface thanks to the establishment of a thorough quality control system using cutting-edge inspection equipment. Excellent. Poongsan's copper and copper alloy rolled products are produced in a variety of ways, including pure copper, brass, phosphor bronze, nickel silver, cupronickel, and special alloy (PMC26 and other) depending on the alloy composition and casting method. In particular, in response to market demands for new high-strength copper alloys due to technological advancements such as the Internet of Things and electric vehicles, we have developed new alloys (P1000HS and others) and are applying them to high-tech products requested by customers.

The NSP-5 is an all-weather, multimode, Ku-band radar designed to fly on Group 3-4 Unmanned Airborne Systems (UAS). Its low-Size, Weight, and Power (SWaP) design means ample room for other onboard sensors, such as Electro-Optical and Infrared (EO/IR) cameras. This means users can understand the bigger picture. The NSP-5 is capable of performing spot and stripmap Synthetic Aperture Radar (SAR) and Magnitude Change Detection (MCD), as well as Moving Target Indication (MTI) collections in a variety of maritime and land environments in all weather conditions. This includes smoke, fog and other obscurations where the operators do not have a clear view of the terrain below them. The NSP-5 has a proven track record of reliability and has a recommended maintenance interval of 2,000 hours. Additionally, the modular design makes the NSP-5 easy to integrate onto most platforms.

FLAMEMASTER has formulating and compounding capabilities for sealants, adhesives, and coatings made from polysulfides, epoxies, silicones, and rubbers, among others. The product line includes corrosion-resistant materials, mid- and lightweight sealants, electrical potting compounds, and thermal barriers.

EDS is applied high-power LED light source to achieve fast target acquisition of shooter. With an efficient LED light source, EDS guarantees more than 50,000 hrsof operation time (Continuous use). EDS allows for better situation awareness and fast target engagement especially from non-standard shooting position. EDS can be used for hunting/recreational purpose.