Continental connectors are manufactured with highest quality materials. Our contacts are machined to close tolerances as opposed to stamped and formed styles. All molding compounds are glass reinforced, flame retardant and able to withstand severe environmental and mechanical requirements. Military connector families conform to the highest Defense Supply center (DSCC) standards, which require qualification testing and continued periodic requalification under the surveillance of government representatives to maintain our Company Qualified Product Listing (QPL)

Pandion Perception provides a robust solution for autonomous navigation, Advanced Driver Assist (ADAS) and mapping in GPS-denied environments, efficiently generating the low-latency spatial data that every autonomous system needs. Mounted on ground vehicles or uncrewed platforms, our 3D spatial sensing systems enable operation environments where GPS is degraded or denied - such as dense urban areas, subterranean infrastructure, or contested military theatres. These capabilities are tailored for missions and logistics operations, offering reliability and precision where traditional systems fail.

The high performance of the aerospace industry, in both technical and economic aspects, is due in part to its control over the supply chain and its quality throughout the value chain (from the buyer to the SME providers). For GIFAS, it is imperative to continue in this way to keep the industry competitive.

The RFcore Radar series are FMCW type radar and were developed to detect/track small air targets. The major difference between three models is detection performance. RX32B is fundamental model. RX128B have four times larger radar than RX32B. RX192A have six times larger radar then RX32B. The number of the product name means the number of antenna elements. All have compact and lightweight physical architecture that concentrates all the components required for radar, such as antenna, RF components and radar signal processor, in a small single housing. Transport can be carried in the carrier box and can be easily carried by one person. For installation, you can use a commercially available camera tripod. The weight is about 7.5kg (RX32B) and 15.9kg (RX128B), and the lower connection part is compatible with the tripod connection for the camera. Power supply requires 12VDC (RX32B) and 24VDC power (RX128B and RX192A). When using a battery, it is possible to connect a 12V battery or 24V battery to radars. Usage time may vary depending on the battery capacity. RFCORE recommended the constant power supply. Transfer of Status and BIT information and simple control of the RX32B, RX128B and RX192A are possible with a web browser using the Ethernet connection for authorized users. Using the terminal program provided with the radar, you can view the radar control and detected target information in real time. All RX Radar series’ Power Amp and Core Chip were designed using RFcore's own products.

InspecX is a next-generation autonomous swarm inspection system for aircraft. It is addressing challenges in the $100B global aviation maintenance market. Airlines face a shortage of certified technicians, with Boeing projecting demand for over 700,000 by 2044. Aircraft-on-ground (AOG) incidents cost $10,000–$150,000 per hour, making downtime reduction critical. InspecX uses swarm coordination and LiDAR-based SLAM to perform safe inspections in GNSS-denied or indoor environments. It reduces required technicians from 9 to 3 and inspection time from 10 hours to 3, achieving over 50% cost savings for large aircraft. Beyond efficiency, InspecX helps airlines avoid AOG losses, accelerates maintenance cycles, and improves airworthiness. By maximizing fleet readiness and ensuring reliable operations, it provides a scalable, future-proof solution. InspecX is positioned to become the new global standard for aviation safety and maintenance in the era of intelligent mobility.

MPS Microsystems is specialized in manufacturing high-precision, miniature linear bearings. We offer a comprehensive range of exceptionally smooth bearings with bore diameters from Ø 2 mm to Ø 6 mm. The balls of these precision bearings meet ‘Grade 3’, the highest quality defined by the ISO 3290/DIN 5401 standard. Combined with a cage and a high precision casing, they allow rapid positioning while reducing friction and eliminating the stick-slip effect. The standard version of MPS Microsystems linear bearings consists of a stainless steel bushing and balls, and a brass cage. An all-stainless steel version or one with ceramic balls can be made on request.

The NIDV supports its members in both the national and international markets in as many ways as possible. From participation in international projects, international trade fair visits to programs with government support. You can find more information about these initiatives below. International projects The NIDV organizes various opportunities for its participants to improve their international opportunities. The NIDV facilitates international trade fair participation, matchmaking events with international Original Equipment Manufacturers (OEMs) and meetings about international opportunities. Trade fairs and trade missions Participation in trade fairs takes place in close consultation and collaboration with a number of departments. The Ministries of Foreign Affairs, Defense and Economic Affairs are involved in the activities. For the government part, the RVO is involved in the creation of the Dutch pavilion and hospitality lounge with the help of the Ministry of Economic Affairs and Climate Policy. In addition to trade fairs and trade missions, the NIDV actively participates in various international projects. Partners for International Business (PIB) Partners for International Business (PIB) is a program that allows Dutch companies to realize their international ambitions in a public-private partnership. Doing business abroad is not always easy. You may encounter trade barriers, insufficient knowledge among local governments and companies, or adverse local legislation. Collaborating with other companies in the sector and the Dutch government can ensure that you are in a stronger position. Alliance II The NIDV will participate in EU-ALLIANCE II from 2021 to 2023, this European project aims to support SMEs on the international market in the field of technical textiles, connectivity and advanced materials on “dual use” markets in four target countries , namely: United States, Canada, Japan and Indonesia.

KJF designed and fabricated passenger, service and cargo door assembly toolings for sukhoi superjet 100.