ElectroAir’s mobile APA-65 -series combined units consist of frequency converter units (AC rated output power up to 45 kVA) and rectifier units (DC continuous current up to 800A). These units are intended for the ground servicing of all aircraft types with a frequency of 400Hz and voltage 115/200 V and to power on-board electrical equipment and launch aircraft/ helicopters with a voltage of 28.5 VDC. APA-65 series is designed to eliminate CO2 emissions with its unique technical characteristics. Diesel hybrid unit and battery driven unit - unit can perform the complete service of aircraft at remote parking places with diesel engine / through batteries and it is also capable to operate from the 50/60Hz, 400V, 3 phase main power supply grid as any electrical GPU, without fuel consumption and with zero operating emissions. The range of different APA configurations with no emissions allow for safer, cleaner and more practical operational conditions for operators and personnel at the location. These units are very compact in size and weight.

Superior Performance: Stable braking power under extreme operating conditions, from taxiing to high-speed landings. Proven Reliability: Robust structures and advanced materials that guarantee long service life with minimal maintenance. Optimized Safety: Redundant design features and compliance with international aviation standards to meet the highest levels of operational safety. Custom Solutions: Tailored brake designs to fit the specific requirements of fixed-wing aircraft, rotary aircraft, and unmanned aerial platforms.

The mRO-50 Ruggedized is a breakthrough microwave optical double resonance (MODR) low SWaP-C Miniaturized Rubidium Oscillator designed to meet the latest commercial, military and aerospace requirements where time stability and power consumption are critical. It provides a one day holdover below 1µs and a retrace below 1E-10 in a form factor (50.8 x 50.8 x 20mm) that takes up only 51 cc of volume (about one-third of the volume compared to standard rubidiums) and consumes only 0.36W of power, which is about ten times less than existing solutions with similar capabilities. The mRO-50 Ruggedized Oscillator provides accurate frequency and precise time synchronization to mobile applications, such as military radio-pack systems in GNSS-degraded or denied environments. Its wide-ranging operating temperature of -40° to +80°C is also ideal for: Underwater Applications, Military Communications, Radars, Low Earth Orbit, Electronic Warfare, Airbornes & Avionics, UAV/UGV/USV/UUV

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

Titanium Grade 1 Strip Titanium Grade 2 Bars-Sheets and Plates-Tubes and Pipes Titanium Grade 5 ELI Bars-Sheets and Plates Titanium Ti-6Al-7Nb Bars

specialized heat shrink tubing for the defense industry, with international standards such as QPL SAE AS23053, DEF STAN 59-97, VG 95343, and BS G198.

Hyundai Rotem's UGV has adapted the top-notch autonomous driving technoolgies from Hyundai Motor Group, capable of search and reconnaissance missions as well as munition transport. Fielded in real operation after approval by the ROK Army in 2021, its technologies were also appreciated in major events such as National Armed Forces Day and Combined Joint Live Fire Exercise.

This KF-21 fighter jet model is produced using advanced SLA (Stereolithography) additive manufacturing technology, providing both intricate detail and structural precision. Manufactured with industrial-grade ABS material, the model benefits from our fleet of six SLA machines, ensuring consistent quality and scalability for various production demands. Our in-house post-processing team delivers a wide range of finishing options, including custom color applications tailored to client specifications. Our company’s origins are rooted in expert prototype fabrication, and we have since evolved into a leader in additive manufacturing technologies. We support OEM production and prototype mock-up projects for diverse clients, building a reputation for technical excellence and collaborative development. The KF-21 model highlights our capabilities in precision model making, turning innovative designs into high-quality finished products.