The AI Inspection Rover is capable of autonomous driving indoors and outdoors, obstacle avoidance, high-resolution image acquisition, aircraft underbody inspection, and platooning. Its low-height design allows it to pass under the aircraft, and with its zero-turn function, it can execute missions more efficiently. Additionally, it can drive slopes of up to 10° and overcome bumps of up to 30mm.

Cooled thermal imaging camera module F/#4.0 • Detector type: Cooled InSb 15μm (640 x 512) • NETD: <20mk typical (without lens) • Continuous ZOOM LENS • Continuous Digital Zoom • Advanced image processing - Auto Gain Control (AGC) ) - Adaptive Histogram Equalization (Adaptive HEQ) - Local Area Enhancement (LAE) - Digital Detail Enhancement (DDE) - Denoise Reduction (DNR) - Sharpness • MTTF (Mean Time To Failure) 15,000 hours • Various color sets (WhiteHot / Rainbow / Twilight / TwilightShifted / Turbo / Iron / Plasma)

Adjustable stator vanes that control airflow angle entering the rotor blades.

To date, we have experience producing more than 10,000 pieces and have the ability to produce an average of 500 molds per year.

RFcore has been innovating MMIC solutions for phased array system pursuing more ease of use, higher performance, higher level of integration as well as lower cost. We believe that the most suitable way is exploiting properties of God gifted semiconductor Silicon and GaN. We aim at integrating all components of TRM for active phased array on single die and even multi-channel TRM too.

Developed by MPS Microsystems, the voice-coil nano-positioner unites a Lorentz-force motor, flexure guidance and on-board electronics inside a 65 × 60 × 38 mm envelope. Standard travel is 2.88 mm, extendable to 7 mm with the same coil, suiting microscope objectives, small mirrors and sensors that demand friction-free motion. Bidirectional repeatability stays within ±1 µm over a 360 µm stroke and ±2.5 µm across the full stroke. We can tailor mounting plates, objective clamps and cable exits to suit your specific requirements, ensuring that this voice-voil actuator can be integrated seamlessly into your system.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

The ARTUS Lite’s prowess extends to tele-operation scenarios, particularly within military, nuclear, and bio-pharma applications, where an end-effector that operates with both finesse and confidence is crucial. It provides a safe and precise solution for remote manipulation in hazardous or inaccessible environments, proving vital in environments where the safety and replacement of manual labor are urgent concerns. It excels in machine tending and pick-and-place automation within greenhouses, warehouses, and recycling facilities, enhancing productivity while prioritizing worker safety.