The maximum transmission distance varies based on the following frequency-related specifications. Camera Frequency Max Cable Length ================ =============== 20 ~ 60 MHz 10 m 60 ~ 80 MHz 7 m 80 ~ 85 MHz 5 m  In cases where a single PC cannot handle large amounts of image data, it becomes necessary to duplicate the image and use multiple PCs for processing. A splitter is required in such scenarios.  The CLS-30T2S amplifies and transmits image signals from a single camera to up to two PCs, supporting Base/Medium/Full configurations (10 Taps supported).  The Master side transmits RS232 and CC1~4 signals, while the Slave side replicates and transmits image signals only.

Supports non-destructive inspection of aircraft composite skin structures and is composed of a piezoelectric layer sensor, data acquisition equipment, and damage analysis software. Utilizes piezoelectric sensors to generate Lamb-wave and acquire signals, collecting data to accurately detect and assess composite damage. Visualizes inspection results on display such as damage location, size and index. - POD Accuracy: 1 inch 90% or more - POD Precision : Position error within 30 mm - 64 channels / 230 path reference detection time within 10 minutes - Sensor : Resonance resistance less than 400kΩ - Sensor : MIL-STD-810G - Sensor : RTCA DO-160 Section 23.0 - DAQ : x128 Piezoelectric sensor interface

- Inspection robot control and damage assessment for robot operators. - Pre-inspection information creation for inspection planning. - A 3D user interface for inspection robot status monitoring. - Damage assessment and result report generation capabilities.

This explosive detector, built on a photochemical sensor, is a security device that detects traces of explosives by sucking in the surrounding air. It is scheduled for trial application at APEC 2025.

The ARTUS Lite’s prowess extends to tele-operation scenarios, particularly within military, nuclear, and bio-pharma applications, where an end-effector that operates with both finesse and confidence is crucial. It provides a safe and precise solution for remote manipulation in hazardous or inaccessible environments, proving vital in environments where the safety and replacement of manual labor are urgent concerns. It excels in machine tending and pick-and-place automation within greenhouses, warehouses, and recycling facilities, enhancing productivity while prioritizing worker safety.

NICKEL 200 / 201 Bars-Sheets and Plates-Tubes and Pipes MONEL® ALLOY 400 Bars-Sheets and Plates-Tubes and Pipes MONEL® ALLOY K-500 Bars INCONEL® Alloy 600 Bars-Sheets and Plates-Tubes and Pipes-Wire INCONEL® Alloy 601 Bars-Sheets and Plates-Tubes and Pipes-Wire INCONEL® Alloy 625 Bars-Sheets and Plates-Tubes and Pipes INCONEL® Alloy 625LCF® Sheets and Plates INCONEL® Alloy 693 Sheets and Plates-Tubes and Pipes INCONEL® Alloy C-276 Bars-Sheets and Plates-Tubes and Pipes INCONEL® Alloy 22 Bars-Sheets and Plates-Tubes and Pipes INCOLOY® Alloy 800 H / HT Bars-Sheets and Plates-Tubes and Pipes INCOLOY® Alloy 825 Bars-Sheets and Plates-Tubes and Pipes Titanium Grade 1 Strip Titanium Grade 2 Bars-Sheets and Plates-Tubes and Pipes Titanium Grade 7 Bars-Sheets and Plates-Tubes and Pipes

The static-dynamic mixer vipro-DUOMIX is perfectly suited for compressible, two-component materials – with very different viscosities, extreme mixing ratios and high-pressure sensitivity. The extended version with optimized mixing blocks for low-viscosity, and high-viscosity materials on either side brings a further advantage: It is ideally suited for materials that are difficult to mix – with different or identical viscosities. A modular design with five different dispenser sizes per side allows complete flexibility. And a wide range of mixing ratios from 1:1 to 100:1. The vipro-DUOMIX can be used for complex two-component applications in diverse industries such as automotive manufacturing, aerospace, or electronics. Irrelevant of whether it is for a dot dispensing, a bead application or for a potting application. Particularly in the production of aircrafts the static-dynamic mixer is used for honeycomb potting or for edge sealing. Special nozzles with adjustable bead width are available for this purpose. A wide range of two-component materials based on e.g., polyether, epoxy resin, silicone or polyurethane can be dispensed in all areas of application. Due to the parallel alignment of the dispensers, and due to a weight-optimized design, the vipro-DUOMIX is very compact – ideal for assembly in robotic cells or for automated applications.

Electric motor used to drive the joint (WT axis) of the Explosive Ordnance Disposal (EOD) Robot.