Nas-52 or Night Attachable Sight gives law enforcement and military personnel the versatility in operations through attaching simple night vision device prefixed to daytime sight which makes available to engage in surveillance or to acquire targets regardless of ambient light conditions. NAS-52 is a clip-on system designed to mount in front of any kinds of daytime riflescope, and it gives daytime riflescope the night vision capability. Sniper or designated shooter using daytime scope will significantly need this performance for night time operation.

The EXOpod is the most advanced cubesat deployment system on the market. It is available in 6U/8U, 12U and 16U sizes which can be broken down into smaller slots to accommodate cubesats of any size. EXOpod Nova, the latest generation of the EXOpod line, is rapidly expanding what the cubesat design standard (CDS) is capable of – cubesats launching with Nova can now increase the volume of their lateral protrusions by 400% and their mass by 30%, enabling a wider and more powerful array of satellite designs and use cases.

A Main Generator installed in the KUH series that supplies system power.

Ultra-High Accuracy MEMS Certus Evo features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Certus Evo’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Certus Evo is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. AI-Based Algorithm Certus Evo features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. Dual Antenna RTK GNSS Certus Evo contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus Evo contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi Protocol Support Certus Evo features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

Low Size, Weight and Power (SWaP) at only 297g. Up to 100 TOPS GPU by NVIDIA® Jetson Orin™ NX Supports multiple camera and sensor interfaces 2x GbE and 2x USB3 for RGB/ Infrared/ hyperspectral cameras and lidar/ radar 2x GMSL2 for HDR/ 3D cameras Built-in UART and CAN to interact with flight controller 1x M.2 2230 for storage and 4G/5G communication ready Supports 4S-14S drone battery pack Compatible GMSL2 cameras with pre-built drivers

- Urban drones specialized in surveillance/spatial information/disaster safety/facility survey - Completed localization of core components! Equipped with encryption KCMVP Dimensions (WxLxH) : Flight / 360x360x160mm(h) Folding / 260x260x160mm(h) Airframe Weight : 2kg or less (max take-off weight) GNSS : RTK / GNSS (SBAS supported) Flight Time : 30 minutes

Engine Start Begins with ATS. The Air Turbine Starter (ATS) is a key component of an aircraft's secondary power system, driven by Bleed Air supplied from the Auxiliary Power Unit (APU) to accelerate the engine up to approximately 8,900 RPM, enabling engine start. Through the in-house development and localization of the ATS, we have incorporated power generation, optimal design of the shear section with consideration of failure, Containment functionality, as well as lubrication and power transmission systems. In addition, we have secured manufacturing and assembly technologies and continue development aimed at successful operation and the establishment of a mass production system.