The FOR-10T/R supports Base configurations (including 10 Taps) and enables long-distance transmission of image signals via optical fiber, along with RS232 control signals and CC1~4 trigger signals. These signals are transmitted to the PC. This product supports transmission distances of up to 2 km, and by replacing the optical module, even longer distances can be achieved.  Fully supports the Camera Link interface (Area/Line Scan).  Supports Base (including 10 Taps) configurations (CC1~4, RS232, 10 Ports (Taps), LVAL, DVAL, FVAL).  Supports pixel frequency from 20 to 85 MHz.  Maximum transmission distance: 2000 m.  Enables lossless transmission.  Supports all external full-duplex RS232 communication speeds on a single port.  Features a locking DC power jack (Molex).  Camera link Connector Type : SDR connector.

Consists of a Data Transmission and Recording Unit (DTRU) for data transmission and collection, and a Removable Mass Memory (RMM) for data storage. Stores pre-planned flight mission data in the RMM on the ground and transmits it to the aircraft via the DTRU. Collects various mission data (flight data, monitoring data, video data, and audio data) during flight, stores it in the RMM, and transmits it to the ground for mission analysis. - x5 ARINC-818 Recording as H.264 - x2 Analog audio recording - x7 MIL-STD-1553B Bus Monitoring - x2 Gigabit Ethernet Monitoring - 512GB Solid-State Disk (up to 2TB) - Size : 160.1x146.0x232.4 mm - Weight : 4.25Kg - Power : MIL-STD-704F (28VDC, 58W) - Environment: MIL-STD-810G - EMI/EMC: MIL-STD-461G

GE and Safran are evaluating several promising architectures as part of their technology maturation plan. The most ambitious, the one that will yield the gre...

Supports non-destructive inspection of aircraft composite skin structures and is composed of a piezoelectric layer sensor, data acquisition equipment, and damage analysis software. Utilizes piezoelectric sensors to generate Lamb-wave and acquire signals, collecting data to accurately detect and assess composite damage. Visualizes inspection results on display such as damage location, size and index. - POD Accuracy: 1 inch 90% or more - POD Precision : Position error within 30 mm - 64 channels / 230 path reference detection time within 10 minutes - Sensor : Resonance resistance less than 400kΩ - Sensor : MIL-STD-810G - Sensor : RTCA DO-160 Section 23.0 - DAQ : x128 Piezoelectric sensor interface

The SC-SSGMRTM, a Seedcore Co., Ltd representative product, is a backplane transmission module that performs the I/O function of the SSGM(Synchronous Signal Generation Module). When the SSGM(Synchronous Signal Generation Module) board is plugged into the motherboard(Backplane) in front of the Chassis, you can extend the I/O function of the board by plugging the SC-SSGMRTM board into the back of the Backplane. Three 37-pin Micro D-sub ports are used to send synchronization signals generated by SC-SSGM to the outside or to receive external synchronization signals, Three separate MMCX output ports are prepared to support test equipment such as oscilloscopes, and you can convert them to various signals and output them.

Hydraulics International, Inc. (HII), headquartered in Chatsworth, California, U.S.A., is a leading worldwide supplier of integrated products, services and support to military forces, aviation and commercial industries, Government agencies and prime contractors. Focused on defense and commercial technology, the Company develops, manufactures and supports a broad range of systems for over one hundred industries as well as mission-critical and military sustainment requirements over the globe. Our extensive design capabilities enable us to produce the most sophisticated technological units known in the Aircraft Ground Support Equipment (AGSE) profession.

HII has been recognized as one of the largest defense ground support equipment technology companies in the world. We hold leading market positions in ammunition loading systems, aircraft hydraulic system testing, aircraft cabin pressure testing, power systems, environmental control systems, military trailers, high-pressure gas and liquid systems, flow measuring equipment, and integrated logistics and support services.

Our corporate, engineering and manufacturing facilities, located in Chatsworth, CA and Forsyth, GA, encompass over 625,000 sq. feet of production space. Our manufacturing facility is equipped with state-of-the-art equipment such as CNC lathes and mills, computerized tube bending, full sheet laser and waterjet, automatic press brake and programmable punch press, laser topography scanners, and other quality verification devices.