MONEL® ALLOY 400 Bars-Sheets and Plates-Tubes and Pipes MONEL® ALLOY K-500 Bars INCONEL® Alloy 600 Bars-Sheets and Plates-Tubes and Pipes-Wire INCONEL® Alloy 625 Bars-Sheets and Plates-Tubes and Pipes INCONEL® Alloy 625LCF® Sheets and Plates INCONEL® Alloy 693 Sheets and Plates-Tubes and Pipes INCONEL® Alloy 718 Bars-Sheets and Plates INCOLOY® Alloy 800 H / HT Bars-Sheets and Plates-Tubes and Pipes INCOLOY® Alloy 825 Bars-Sheets and Plates-Tubes and Pipes INCOLOY® Alloy DS Bars-Sheets and Plates INCOLOY® Alloy 330 Sheets and Plates

As a leading manufacturer in the world’s marine engine market, STX Engine provides all services related to design, manufacture, sales, after-sales services, etc., and is responding to diversifying market demands and severe regulations based on its long experience and know-how.

An Angle of Attack (AOA) indicator is a flight instrument that shows a pilot the angle between the aircraft's wing and the oncoming air, providing a crucial safety margin by warning of an approaching aerodynamic stall. Unlike airspeed. A Vertical Speed Indicator (VSI), also known as a Rate of Climb and Descent Indicator (RCDI) is an instrument which indicates the rate of climb or descent of an aircraft. These devices are installed and compatible with F-16 series aircraft and KAI's T-50/FA-50 series aircraft.

Hermetic connectors are essential to maintain system integrity in applications where the reliability and performance of electrical connections is critical, such as gas-tight barriers or high-pressures differentials.

Low Size, Weight and Power (SWaP) at only 297g. Up to 100 TOPS GPU by NVIDIA® Jetson Orin™ NX Supports multiple camera and sensor interfaces 2x GbE and 2x USB3 for RGB/ Infrared/ hyperspectral cameras and lidar/ radar 2x GMSL2 for HDR/ 3D cameras Built-in UART and CAN to interact with flight controller 1x M.2 2230 for storage and 4G/5G communication ready Supports 4S-14S drone battery pack Compatible GMSL2 cameras with pre-built drivers

Between Earth and space: stratosphere-compatible, solar-powered high-altitude aircraft, known as HAPs (High Altitude Platforms), offer a sustainable alternative to satellites for Earth observation and communication. They are reusable, cost-effective and flexible in use. The DLR joint project HAP-alpha is developing such a technology demonstrator and is endeavoring to establish a complete system capable of permanent operation. The aim is for DLR to build up comprehensive expertise for the development of high-performance, high-flying solar aircraft and to play an active role in shaping the legal framework. In summer 2025, the HAP-alpha successfully passed a ground vibration test.

To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

Key Features of Ophir's IR lenses for thermal weapon sights and hand-held thermal imagers: • Precision Engineering: Our lenses are designed with precision engineering, guaranteeing exceptional clarity and image quality in the LWIR spectrum. • Versatile Compatibility: Ophir's lenses seamlessly integrate with a wide range of platforms, including hand-held thermal imagers and thermal weapon sights. This versatility ensures adaptability to your specific application requirements. • Enhanced Thermal Imaging: Experience superior thermal imaging performance that enables accurate detection, identification, and tracking of targets, even in challenging environmental conditions. • Robust Build Quality: Our lenses are built to withstand the rigors of field use, ensuring durability and longevity in demanding situations. • Exceptional Clarity: Achieve clear, high-resolution thermal images, allowing you to make critical decisions with confidence. • Competitive Advantage: Stay ahead of the curve with MKS Ophir's cutting-edge thermal imaging technology, giving you a competitive edge in your field of expertise. When it comes to thermal imaging lenses for thermal weapon sights and hand-held thermal imagers, Ophir is your trusted partner for excellence. Explore our range of products to discover the perfect solution that will elevate your application's performance. Contact us to set a meeting at ADEX Seoul