Rolatube IAM (Integrated Antenna Mast) is a lightweight, man-portable communications mast that integrates a high-efficiency dipole antenna directly into its structure—redefining rapid tactical deployment. Built from Rolatube’s proprietary bistable composite, the IAM unrolls to full height without tools, enabling users to connect and transmit in seconds. Available in 3.5 m and 7 m models, the mast weighs just 1.9 kg and packs down to a 150 mm roll, offering unmatched portability for dismounted operations. Designed for reliable RF performance, the IAM ensures no signal loss when in contact with grounded surfaces. Its embedded omni-directional dipole antenna delivers superior range and VOR communication performance compared to traditional systems. The 3.5 m IAM comes in VHF (30–300 MHz) and UHF (136–470 MHz) variants, each available in four colours, with a top-cap socket for L-Band antenna integration, extending the system’s use to applications such as telemetry, GPS, and aircraft surveillance. The mast can be handheld, guyed, or elevated via an integrated rigging point, and is engineered to meet MIL-STD-810G, fully maintenance-free, and resistant to water, dust, and UV. With a wind rating of 100 km/h (62 mph) when guyed, the IAM stands up to demanding field environments while delivering high-performance, elevated communications infrastructure at the tactical edge.

Receives vibration signals from an accelerometer installed on the aircraft engine and monitors engine vibration. Processes real-time vibration signals and converts them into IPS AVG units for output. Developed for localization, achieving 50% cost competitiveness compared to equivalent products. - x1 MIL-STD-1553B - x2 UART(RS-422/485) - x2 Accelerometer sensor - Sample rate : Up to 5,000Hz - Size : 220 x 206 x 52 (mm) - Weight : 1.75Kg - Environment : MIL-STD-810G - EMI/EMC : MIL-STD-461G - Power : MIL-STD-704F (28VDC, 10W)

The maximum transmission distance varies based on the following frequency-related specifications. Camera Frequency Max Cable Length ================ =============== 20 ~ 60 MHz 10 m 60 ~ 80 MHz 7 m 80 ~ 85 MHz 5 m The PoCL Bypass function supports Power over Camera Link (PoCL) operation from the Frame Grabber to the selected camera. However, the power supply to unselected cameras is automatically disabled. To prevent power cutoff, separate power must be provided to the cameras. Configurations are available as follows, including image signal amplification. [Features of CLM-30C4]  Fully supports the Camera Link interface (Area/Line Scan).  Provides manual (switch) or remote (RS232) camera selection.  Allows selection from one of four cameras configured for Base (Layer 1) or Medium/Full (Layer 2) levels.  Supports Base/Medium/Full setups (CC1~4, RS232, LVAL, DVAL, FVAL)  PoCL bypass function: Automatically powers only the selected camera when PoCL-compatible cameras, frame grabbers, and cables are used.  Supports pixel frequency from 20 to 85 MHz.  Supports PoCL signal bypass (patented).  Enables lossless transmission.  Provides additional full-duplex RS232 communication at up to 256 Kbps.  Features a locking DC power jack (Molex).

i3system’s line scanning X-ray detector platform, XID-C15DP/XID-C24DC, is a high performance and cost effective solution for dental panoramic, cephalometric applications. i3system’s direct type sensor ensures the most sharp images among the current products in the market. XID series is designed for compact size and easy installation. High DQE(Direct Quant㎛ Efficiency) enables high performance at lower dose of X-ray. Introduction Indirect type X-ray detector uses the scintillator and the photo-diode(CCD or CMOS sensor) for conversion of the X-ray into the light and for taking images espectively. But the light scatters and goes extinct during it passes through the scintillator and reaches to the CCD or CMOS sensor. As a result, it is inevitable to get blurred image. In the mean time, XID C15DP, direct type detector, converts X-rays into electronic signals directly without conversion process of light. Because X-ray is not converted into light, it provides much sharper images than indirect type detector. XID C15DP is designed to compact for easy installation. It provides Gigabit Ethernet port on the detector for easy configuration. Instead of Gigabit Ethernet, camera link or optical interface can be provided according to requirements of users.

This miniature fin actuator manufactured by MPS Microsystems was designed based on customer specifications. Designed to guide a very small object and disposing of an extremely limited space, it meets strict requirements in terms of performance, weight - less than 100 g - and dimensions. To reduce the length of this actuator, MPS Microsystems used part of the screw length as the motor axis. This screw is equipped with a very compact 4-point contact bearing that simultaneously absorbs axial and radial loads. The angular play on the aileron axis is less than 0.1° rms. This actuator meets the storage and vibration requirements of military equipment.

GE's T901 Engine for ITEPA test cell is not a combat mission. In combat, there is no time for an unproven design. With more than 100 million flight hours of ...

Customized Market Research answers questions about an overseas market including market trends and size, customary distribution and promotion practices, market entry requirements, regulations, product standards and registration, key competitors and potential agents, distributors, or strategic partners. Rural America's Intelligence Service for Exporters (RAISE) helps rural businesses identify new markets, find industry-specific market intelligence, or identify potential business partners in a country.