Features NO MELT, NO DRIP (50/50 Nylon Cotton) Moisture control system for comfort and breathability Elbow protector insertable PALS webbing on lower sleeves for scalability Reliable components (YKK military zipper, etc.) Composition Sleeves: Nylon 50%, Cotton 50% Body: Functionalized Polyester Size 95 ~ 115 Colors MC (MultiCam) BMC (Black MultiCam) BK (Black) RG (Ranger Green) CYT (Coyote Brown)

Developed by MPS Microsystems, the voice-coil nano-positioner unites a Lorentz-force motor, flexure guidance and on-board electronics inside a 65 × 60 × 38 mm envelope. Standard travel is 2.88 mm, extendable to 7 mm with the same coil, suiting microscope objectives, small mirrors and sensors that demand friction-free motion. Bidirectional repeatability stays within ±1 µm over a 360 µm stroke and ±2.5 µm across the full stroke. We can tailor mounting plates, objective clamps and cable exits to suit your specific requirements, ensuring that this voice-voil actuator can be integrated seamlessly into your system.

An AI-powered geospatial intelligence platform that allows users to interact with satellite imagery through natural language. By integrating LLMs with advanced image processing and object detection, SatCHAT makes EO data accessible to non-experts, enabling real-time infrastructure monitoring, event detection, and automated reporting. This lowers the barrier for industries to leverage satellite insights.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Next-generation wheeled military vehicles are essential to secure maneuverability and survivability for efficient power operation even in the worst weather and terrain conditions, so we have developed a run-flat product with pure domestic technology that can drive to a safe zone where tires can be repaired and replaced with quality that meets the standards of the United States and NATO (North Atlantic Treaty Organization) while ensuring stable steering and driving performance by applying our unique design in the event of tire pressure loss due to tire damage. Based on this, we produce and supply run-flat-related products to wheeled military vehicle manufacturers.

The SCXMC-SFPDP is a high-speed optical communication card that operates through the XMC interface of the SBC. It is designed to transmit and receive large volumes of data between the SBC and other devices in real time. Unlike Ethernet, which can be difficult to synchronize, the SCXMC-SFPDP uses optical communication with synchronization signals, enabling precise and high-speed data transfer. It offers low response latency (<40 µs) and supports four transmit/receive channels at 3.125 Gbps per channel. A device driver program is required for operation, and the Linux driver can be downloaded from Seedcore’s product page. Drivers for other operating systems can be developed upon request. This module is deployed in the L-SAM multi-function radar system to ensure reliable real-time data transmission between mission-critical subsystems.

The L Series comes with frames in various lengths to accommodate a variety of module combinations. The frames range from a basic frame with just 2 side rails and 2 end caps, to more complex versions with jackscrews, backshells, cable clamps, etc.

Engineering is ABC's DNA. The areas of predilection are mainly: Fluidics (liquid and and gaseous) Electricity (strong and weak currents) Mechanics and heat Automation (PLCs and IT) Electronics Software engineering Each of these areas translates into measures in a global system approach. Our teams are involved in the functional knowledge of equipment and customer systems ...