STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

This system product is a product that directly supplies and heats lubricant oil for smooth operation of the main engine cylinder’s metallic and mechanical movement. Lubricator, a product that supplies lubrication directly to the main engine cylinder liner, can control injection timing and consumption using an electronic control method that responds to the movement of the main engine piston. The alpha lubricator system is based on an algorithm controlling the cylinder oil dosage proportionally to the sulphur content in the fuel and, fuel consumption on particular load of engine. Minimum cylinder oil dosage is required to provide an adequate oil film and detergency properties. Everllence and WIN GD engines are currently applying the second generation Lubricator type, the Everllence type is Mk-I and the WIN GD type is Mk-ε (Epsilon).

The Crane stands as a state-of-the-art Mid-Wave Infrared (MWIR) detector. This device features a 5-megapixel resolution in a 2560×2048 format with a fine 5μm pitch. It is based on SCD's established XBn technology or Hot Full Midwave (HFM) and incorporates a digital readout circuit developed using an advanced CMOS process. The High Operating Temperature (HOT) Focal Plane Array (FPA) functions efficiently at 150K or 120K, enabling a large-format detector that excels in image quality while maintaining a relatively compact size, weight, and power consumption. SCD continues to lead in innovation.

The IntuVue RDR-7000 is fully automatic and does'nt require active pilot adjustments of tilt and/or gain for operation. Reducing workload, allows pilots to focus on flying the most comfortable and safest route through weather. Engineered to provide far superior reliability, accuracy and durability than legacy magnetron-based radar systems, the RDR-7000 offers customers the flexibility to remotely enable advanced software features to provide them the clearest view of weather conditions around the routes they’re accustomed to flying. Key Honeywell Advantages: Next generation -fully automated, higher resolution weather radar system with airborne ground/sea mapping system Reliable and efficient - solid-state transmitters utilizing pulse compression provide reduced weight and power consumption, advanced coherent processing, and increased reliability Compact and easy to install - RDR-7000 IntuVue radar systems technology integrated into a small, lightweight package Available software upgrades - advanced features can be added at any time, including turbulence detection, advanced mapping, target detection and additional hazard features (lightning and hail detection), and forward looking (predictive) windshear Honeywell's RDR 7000 Radar helps in operational costs savings by reducing the delays & downtime caused due to hailstorm, weather incidents and windshears while optimizing routes to reduce diversions and turnbacks.

The MIL-DTL-5015 series of connectors were developed as military standard connectors and applied to various military equipment, it is also used in general industries, medical care, electric vehicles, robots and automation facilities based on its high durability and reliability. This series is threaded coupling and the connection between the contact and the wire is based on soldering. It can be used compatibly with third-party products of the same standard since it is produced according to military standards.

• Contacts • Backshells / protective caps • Solders sleeves / splices • In-line junctions • Identification labels • Wire terminals

THETIS-M2 is a multifunction thermal imaging system that provides soldiers with an advanced, light weight solution for day and night reconnaissance, surveillance and forward observation purposes. It also gives the blue forces a real-time target acquisition and target coordinate calculation capabilities. Thermal Camera + Direct View Optic +Laser Range Finder + Digital Magnetic Compass + GPS

The Glenair next-generation STAR-PAN NG ecosystem incorporates a range of new capabilities in direct response to requests from JTACs, special operations forces, mission commanders, and other military specialists. Design innovations in STAR-PAN NG have resulted in higher current-carrying capabilities, greater versatility in power input support, and real-time plug-and-play USB device integration. The STAR-PAN NG hub and cable series offers a number of interface improvements and circuit board innovation.