It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

Primarily used in medium-sized and large satellites, it provides high torque performance and momentum conservation. By localizing the Control Moment Gyro controller, which had previously been imported for Korea’s domestic satellite industry, Lumir has gained a competitive advantage in both performance and cost.

The SC-DSPRTM, a Seedcore Co., Ltd representative product, is a backplane transmission module that performs the I/O function of the DSP282A. When the DSP282A board is plugged into the motherboard(Backplane) in front of the Chassis, you can extend the I/O function of the board by plugging the SC-DSPRTM board into the back of the Backplane. The DSP282A board consists of two computing nodes. To support this, Ethernet, USB, MMCX, and mini-HDMI ports are allocated to each node, and synchronization signal input ports can also be used simultaneously on both nodes.

Removable shoulder & waist straps can be adjusted to fit the end-user without removing the rack Attaching to select tactical plate carriers with the QASM buckle system or using stand-alone with H Harness Small, medium 4-way stretch Tweave general purpose pouch (Qty.1) Magazine pouches for 5.56mm or 7.62mm mags (Qty. 4) 9mm pistol magazine pouches (Qty. 2) Compatibility : PICO-DSX, PICO-DS, PICO-MBAV, EPIC-FED Composition Material : 500D Cordura® + ARAMID / PV® Colors: MC (MultiCam) BMC (Black MultiCam) BK (Black) RG (Ranger Green) CYT (Coyote Brown)

The era of ultramodern aviation is here. The clean-sheet Gulfstream G500™ unites performance and comfort with revolutionary technology.

Outfitted with high-thrust engines and an aerodynamic new wing, the G500 is built for effortless takeoffs and landings. Enjoy access to short runways and high-altitude airports, coupled with increases in efficiency and reductions in emissions.

The long-range G500 gives you back time with a high-speed cruise of Mach 0.90. Fewer flight hours means longer periods between scheduled maintenance visits, higher potential aircraft value and fresher crews.

The tall and wide G500 cabin offers great flexibility, including the option of a forward or an aft galley and an aft stateroom lit by four panoramic oval windows. You can stroll down a generous aisle or recline in all-new seats. Tables seat three across for meals or meetings.

- 3 axis Fiber Optic Gyroscopes / 3 axis MEMS Accelerometers - Operating Range: ± 490º/sec - Bias Repeatability(over temp. range) : ≤ 0.5º/hr (1σ, RMS) - In-run Bias Stability: 0.03º/hr (typical, 1σ) ≤ 0.05º/hr (max, 1σ) - Angle Random Walk : 0.025º/√hr (typical, 1σ) - Power Consumption: 5W @ 25℃ (< 8 W, @ - 40℃) - Input Voltage: + 5 V Lightweight Package: 790g (1.74 lbs)

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

Additive manufacturing: - enables custom electronics cooling solutions, providing precise heat management, compact designs, and improved reliability for high-density electronic components. - battery coolers offer optimized thermal management, extending battery life, enhancing energy efficiency, and ensuring compact integration in electric vehicle systems. - allows for tailored cooling solutions for electric motors, improving heat dissipation, enhancing performance, and reducing system weight for efficient operation.