1) Fabrication - possible Dismension : ~ D 1200 mm - Surface Errors PV < 79 nm RMS < 12 nm Roughness < 2 nm(Typical < 1nm) 2) Lightweight - lightweight Ratio : up to 82.5 % - Rib Thickness : ~ 2 mm - Face Sheet : ~ 7 mm - Lightweight Design & Fabrication

Frequency signal generator for precise target detection High-frequency resolution design and frequency conversion function using DDS method Main performance Frequency: L-Band ~ Ku-Band Accurate Chirp and Pulse Mode Output Level: +0dBm min Spurious: -40dBc min Harmonic: -50dBc min Phase Noise: High Performance Frequency Sensibility: 50ppm max Port isolation: 50dBc Min Applicable fields Guided weapon tower system and radar system can be applied

Key RADAR in counter-fire warfare to defeat enemy artillery by reversely tracing the trajectory of ballistic missile. Design and Manufacture - Environmental Control Unit - Driving unit - Generator - TR module rack & Antenna Case

- Rader · Detection Range : 1.5~10km, Customizable · Radar Type : AESA - LONG RANGE EO/IR · Identification Range : 3.0km · Optical Zoom : 66x (EO), 22x (IR) - JAMMER · Jamming Distance : 20km (GNSS), 10km @2km (ISM) - RCWS (REMOTE CONTROLLED WEAPON SYSTEM) · Weapon : 40mm AGL, 12.7mm MG · Ammo Capacity : 48 rounds (AGL), 200 rounds (MG) · Lethal and Nonlethal 40mm Air Burst Munition Fireable

TMM-238 is developed and designed for use in operator display for Militray systems. It has 1920 x 1080 pixels visible resolution, which is designed and tailored for use in operator display for Militray systems • 23.8”Inch display, 16:9 / 1920 x 1080 Resolution • HDMI, DP, RGB, input • Full Range Digital Dimming Control • 6 Key Membrane Switch • Power range : DC 24V Input • LCD PANEL backlight unit : LCD Backlight units

The Boreas 50 fiber optic gyroscope (FOG) is a highly accurate and reliable navigation technology. It’s the result of over 25 years of development in partnership with two research institutions. The gyroscope uses a closed-loop optical coil and an advanced spread-spectrum digital modulation technique to improve accuracy, stability, and reliability while reducing size, weight, power, and cost. Gyrocompass North-Seeking The Boreas range of fiber optic gyroscopes (FOGs) can determine heading without needing a Global Navigation Satellite System (GNSS) or a magnetometer. By sensing the Earth’s rotation, the system’s north-seeking algorithm can acquire an accurate heading. This is possible in static and dynamic conditions, even at high latitudes. Reliability Boreas 50 has been designed from the ground up for rugged reliability. Both the hardware and software are tested and certified to environmental and electromagnetic standards (MIL-STD 461 and MIL-STD 810H). The precision aluminum enclosure is waterproof and dustproof to the IP67 standard. The system is resilient to shock and vibration, allowing it to be used in extreme conditions. Industry-Leading SWaP-C The Boreas 50 FOG Series delivers industry-leading performance with a compact and lightweight design. Excelling in terms of Size, Weight, Power, and Cost (SWaP-C). Multi-Protocol Support The Boreas 50 features multiple interfaces, including Ethernet, CAN, RS232, 1PPS, RS422, and GPIOs. It supports industry standard protocols, including NMEA 0183, CANopen, 1PPS, and ANPP, as well as a wide variety of proprietary protocols. A rich, responsive embedded web interface provides full access to all of the device’s internal functions and data. Internal storage allows for up to one year of data logging.

Quapason™ is a high-performance vibratory gyroscope from Safran Electronics & Defense, combining the compactness of MEMS with the reliability of Fiber-Optic Gyroscopes (FOG). It delivers exceptional robustness, ultra-low noise, and high signal stability, making it ideal for stabilization and inertial navigation in harsh environments. Used in weapon turret stabilization, avionics, and artificial horizons, it has surpassed 140,000 units delivered, proving its reliability and precision across civil and military applications.

Our firm offers end-to-end GaN production capabilities, including fabrication, packaging, test, and failure analysis to meet custom requirements. To enable customer designs, a process design kit (PDK) is available with a design manual, sample layouts, and a non-linear device model. Options available include fabrication of customer-designed wafers (“PDK foundry service”) or custom design by TransEON and fabrication according to customer specs (“NRE foundry service”). For either option, volume levels available include pilot/engineering runs, multi-project wafers (MPWs), or full production runs.