Developed by MPS Microsystems, the voice-coil nano-positioner unites a Lorentz-force motor, flexure guidance and on-board electronics inside a 65 × 60 × 38 mm envelope. Standard travel is 2.88 mm, extendable to 7 mm with the same coil, suiting microscope objectives, small mirrors and sensors that demand friction-free motion. Bidirectional repeatability stays within ±1 µm over a 360 µm stroke and ±2.5 µm across the full stroke. We can tailor mounting plates, objective clamps and cable exits to suit your specific requirements, ensuring that this voice-voil actuator can be integrated seamlessly into your system.

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

The AMT-206-1 composite tail rotor blade is a direct replacement for Bell 206A and 206B series helicopter tail rotor blades. Now fitted with a new style of feathering bearings manufactured by KAMATICS. These bearings provide a longer life expectancy, with a patented lining that provides lighter pedal loads and a higher level of chemical resistance, compared to that of the standard fabric Teflon-lined bearings. The AMT-206-1 tail rotor blade has a non-symmetrical airfoil section and incorporates a swept tip. The T/R Blade is primarily fabricated from uni-directional Graphite (carbon fiber) and Aramid (Kevlar™) continuous fibers suspended in an epoxy matrix and is fitted with a nickel abrasion strip on the leading edge. The abrasion strip is bonded on using a urethane adhesive. The AMT-206-1 composite tail rotor blades have a 30% cost advantage, twice the lifespan, higher strength and thrust, and a substantial noise reduction, making them safer and ideal for helicopter operators flying in noise-sensitive areas like national parks and built-up areas.

SKYLIGHT™ is a mono or bi-constellations dual civil/military GNSS receiver, providing the highest navigation performances and operational flexibility. It is suitable for a large range of applications: aircrafts, helicopters, UAVs, missiles, land vehicle.

The fully redundant DA 30-HT-D has been developed for applications with the highest reliability demands. The redundant – two channel – design of the actuator allows continuous operation even if one of the two channels has failed. All major components such as the electric motors, control and communication electronics, and power supply are available twice (redundant). The position sensor features a three channel design (for 2 out of 3 voting). Additionally, there are several sensors integrated to provide diagnostic information such as current consumption, supply voltage levels and temperature readings. All major components of the actuator are continuously diagnosed by the microcontrollers of the actuator and its health status can be read via the redundant RS485.

EMCORE’s TACNAV Light is a field-proven digital compass-based battlefield navigation system. Type-classified by U.S. SOCOM and designed specifically for non-turreted vehicles, TACNAV Light offers: Highlights GPS backup and enhancement, vehicle position, hull azimuth, and steer-to/cross-track error displays One of the lowest cost tactical navigation systems available Improved operational effectiveness and increased force OPTEMPO Application Features Compass for the highest degree of accuracy and unjammable position and navigation information Dead reckoning and odometer interface for accuracy to within 2-3% of distance traveled Digital interface with Battle Management Systems for improved situational awareness Uses TACNAV Universal Multilingual Display (UMD) capable of presenting data in virtually any language Applications Light military vehicles The TACNAV Light is controlled by the Arms Export Control Act (Title 22, USC Sec 2751 et seq.) and the International Traffic in Arms Regulations, ITAR, 22 CFR 120-130, and may not be exported from the United States or disclosed to a foreign person in the United States except as authorized by those regulations.

High-Reliability Space-grade SRAM memory : 1. Density : 16Mbit (512k x 32bit) SRAM 2. Package Type : 100 Pin CQFP (Ceramic Quad Flat Package) 3. MIL-PRF-38535 Class V Qualified 4. Operating Temperature : -40℃ ~ +125℃ 5. Radiation : TID > 102 krad, SEL LETth > 80.4MeVcm2/mg@ 85℃

Lumir developed this new on-board computer in cooperation with Korea Aerospace Industries (KAI) for the CAS500-3 (technology verification satellite), which is scheduled to be launched aboard Korea’s fourth Nuri launch vehicle.