Investigate the smallest of features with spatial resolution down to 600 nm – A state-of-the-art nano-focus x-ray source, precision stages, and high-quality detectors work together to deliver sub-micron resolution imaging. Perform true 4D imaging with Dynamic CT – High temporal resolution, continuous and uninterrupted scanning, and specialized 4D software tools bring synchrotron-like capabilities to the lab. Implement 3D in situ experiments – continuous sample rotation and scanning enable uninterrupted in situ experiments. Dedicated “no-cable-wrap” interfaces simplify experiment set-up. Accommodate a broad range of samples – UniTOM HR’s high power source (50W), multiple detector options (up to 3) and heavy load stage (45 kg) accommodates samples up to 500 mm diameter X 700 mm high. Maximize system utilization and throughput – A fast frame rate detector and a high flux x-ray source combine for high temporal resolution tomography giving you the ability to scan more samples and accommodate more users.

The member companies of GIFAS employ 195,000 people in their aerospace activities in France. These figures do not include temporary workers or the total number of suppliers and subcontractors; this field is estimated to be responsible for 350,000 jobs in France. Our sector is constantly in demand.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

- 1 axis Fiber Optic Gyroscopes - Bias Repeatability: 0.1°/hr - Bias Stability: 0.02 °/h (1,000 sec) - Angle Random Walk: 0.005 °/√hr - Scale Factor Accuracy: 500 ppm - Operating Voltage: 5 V (1 A) - Interface: RS422 Weight: 1.0 kg EMC: MIL-STD-461E

LW-DED 3D printing head module for Morphing Shield Technology. Morphing Shield Technology builds aportable inert gas enviroment surrounding the melting zone for laser wire DED Process.

- To check and verify the RWR system on the aircraft and radiate threat signals to RWR antenna through couplers. - Radiate threat signals to jammer system.

Type : Radial (3P) Size(L,W,H mm) : 193 × 100 × 100 Weight(kg) : 1.7 [Active] N. Speed(rpm) : 3,700 N. Torque(Nm) : 5 N. Power(kW) : 2

Whether satellites, spacecraft or space debris – GESTRA, the "German Experimental Surveillance and Tracking Radar", is a state-of-the-art radar system for observing and tracking objects in space. It operates in the microwave range and explores the Low Earth Orbit of 300 to 3,000 kilometres, i.e. the range in which most satellites and the International Space Station (ISS) are located. This makes it possible, for example, to protect space systems or the ISS from a collision with debris particles by providing a timely warning. Millions of tiny particles orbit the earth and, at a speed of around 28,000 km/h, pose a threat to active space technologies. GESTRA was developed and built by the Fraunhofer Institute for High Frequency Physics and Radar Techniques FHR on behalf of the German Space Agency at DLR.