This solution follows a three-step process of input, processing, and output, utilizing imagery, DEM, AT, and spatial data to refine 3D models. The editing-based texturing function allows users to correct shape errors, occlusions, and distortions, while the automated texturing ensures consistency and accuracy through advanced geometric matching. Final outputs are stored in standard formats for broad practical applications.

The low profile MD145MW-DroneCAN is a 10mm, metal gear, sub 1 oz servo with dual ball bearings, cored motor, and contactless magnetic encoder. This discrete package offers high performance and reliability for robotic and remote, unmanned aerial applications where space is at a premium. Operating via DroneCAN (formerly UAVCAN) control at a wide voltage range from 4.8~7.4 volts, the unique MD145MW-DroneCAN servo produces impressive torque and speeds in its class. #UAV #UAS #UGV

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

Our LiDAR uses a custom-designed laser that separates 1064 nm and 532 nm wavelengths from a single source, with two dedicated receivers capturing each set of data independently. Inside the system, the linear laser beam is refracted at a 10-degree angle through a prism to enable circular scanning. An RF module is also integrated for real-time equipment status monitoring. From circuit board design to component selection, every part of this system was developed in-house by multiple institutions. As a result, we have successfully eliminated reliance on foreign technology.

Weibel’s Doppler 3D tracking radars are designed for precise measurements of free-flying objects such as projectiles, artillery rounds, and rockets. The systems are highly effective for detailed debris tracking, range safety tests, missile tests, and space launches. Weibel’s tracking radars are phased array X-band CW, MFCW and FMCW radar systems consisting of state of the art phased array Doppler radar antennas, high performance pedestals, real-time multi-object tracking processors and state of the art waveform generators, all controlled from the operator console.

INCONEL® Alloy 230 Bars-Sheets and Plates INCONEL® Alloy 600 Bars-Sheets and Plates-Wire-Tubes and Pipes INCONEL® Alloy 601 Bars-Sheets and Plates-Wire-Tubes and Pipes INCONEL® Alloy 617 Bars-Sheets and Plates INCONEL® Alloy 625 Bars-Sheets and Plates-Tubes and Pipes INCONEL® Alloy 718 Bars-Sheets and Plates INCONEL® Alloy X-750 Bars-Sheets and Plates INCONEL® Alloy HX Bars-Sheets and Plates-Tubes and Pipes NIMONIC® Alloy 75 Bars-Sheets and Plates NIMONIC® Alloy 80A Bars-Sheets and Plates NIMONIC® Alloy 90 Bars-Sheets and Plates-Wire-Strip NIMONIC® Alloy 263 Sheets and Plates UDIMET® Alloy 188 Bars-Sheets and Plate UDIMET® Alloy L-605 Bars-Sheets and Plates Waspaloy® Sheets and Plates

This Control Actuation System (CAS) is a guidance system for unmanned flying objects. It consists of three MPS fin actuators that each independently position an aerodynamic fin. The maximum angle of incidence is ±8°, which allows the device to carry out highly precise dynamic manoeuvres. The miniature fin actuators that make up this Control Actuation System are manufactured by MPS Microsystems and were designed based on customer specifications. Designed to guide a very small object and disposing of an extremely limited space, these fin actuators meet strict requirements in terms of performance, weight - less than 100 g - and dimensions. To reduce the length of this actuator, MPS Microsystems used part of the screw length as the motor axis. This screw is equipped with a very compact 4-point contact bearing that simultaneously absorbs axial and radial loads. The angular play on the aileron axis is less than 0.1° rms. This actuator meets the storage and vibration requirements of military equipment.