It is a product produced in Korea and has high performance when used in EO/IR Gimbal for small drones. It can view both VIS and IR images simultaneously and is coupled to a small drone with a small weight to perform operations. Products with manufactured and domestic IR sensors in Korea. we deliver superior technologies that shape the future of defense. Whether supporting ISR missions or enhancing precision in loitering munition operations, MS60 products are designed to ensure operational excellence in the most challenging environments.

Low Insertion Loss, Good IMD Performance RF Coaxial Switches: SPST to SP8T Switches, Transfer Switches from DC to 200 GHz Power Dividers and Power Combiners Wilkinson Types from 2 to 16 Ways Frequency Range from 400 MHz to 26.5 GHz

EMCORE’s IPADS-I (International) provides significant enhancements for today’s Army and Marine Corps survey teams. IPADS offers a proven, reliable, lightweight, off-the-shelf solution developed around four main components. > Compact Position/Navigation Unit (CPNU) > Control and Display Unit (CDU) > Battery and Charger Unit (BCU) > Porro Prism Assembly (PPA) All components are housed in a robust frame that allows for easy component access and stability, while facilitating a ready, two-person transfer between vehicles and aircraft. Features High-precision common survey enables efficient mass fires Impervious to jamming (inertial mode) Embedded Selective Availability Anti-Spoofing Module (SAASM) GPS option Navigation aids (compass rose and digital maps) In-vehicle and offset survey Combat-proven Embedded Built-In Test (BIT) High reliability MTBF, low mean time to repair (MTTR) No periodic calibration required Applications Artillery Survey to Mark: Survey Control Point (SCP) position; used to initialize weapon systems Orienting Line (OL) position and azimuth; used to initialize and align artillery assets

A REDCOM SVG system consists of one or more REDCOM Sigma® SVG-1200 units and a series of standard production General Dynamics Sectéra vIPer phones. Each REDCOM SVG-1200 can interface with up to 12 vIPer phones, which act as voice encryptors for TDM or VoIP voice networks. The encryptors allow any line, trunk, or conference port to conduct secure voice communications with any SCIP-capable device. If more than 12 secure talk paths are required, multiple SVG-1200 units may be networked together.

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.

정상적인 신호 수신을 방해하는 재밍 (Jamming)을 극복하고 안정적인 위성신호를 수신하는 안테나를 독자개발하였습니다.

Camera Frequency Max Cable Length ================ =============== 20 ~ 60 MHz 10 m 60 ~ 80 MHz 7 m 80 ~ 85 MHz 5 m The CLR-30x2 transmits two independent sets of Base, Medium, or Full configuration Camera Link video signals (supporting up to 10 Taps per set) to a PC frame grabber. Each transmission layer can be configured independently .