Hyundai Rotem's UGV has adapted the top-notch autonomous driving technoolgies from Hyundai Motor Group, capable of search and reconnaissance missions as well as munition transport. Fielded in real operation after approval by the ROK Army in 2021, its technologies were also appreciated in major events such as National Armed Forces Day and Combined Joint Live Fire Exercise.

r-TWR are digital towers which enable the remote use of air traffic services (ATS) from any location. Being at an airport, air base or at a centralised location, distance is no longer a factor. The r-TWR functions can be integrated to a traditional tower as a hybrid solution, and can support the ramp and apron management using the same information. It can also be deployed and put in place when needed. Through the use of digital camera technology and sensors, operators can effectively conduct and manage various services remotely, based on visual surveillance. This removes the need to be on-site and occupying critical space at an airport, in favour of a chosen location.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Digitally recorded distressed and alarmed birds, along with the sounds made by their natural predators are broadcast through high output weather-resistant speakers. This triggers a primal fear and flee response. Super easy installation figure makes the systern portable across crop and place Replaceable, customizable species specific bio- acoustic sound chip according to birds kinds and specific regions Effective Coverage: Up to 50m for one single direction, approximately 5,000 square meter Technology integrated operation system enables sound duration and interval to prevent habituation to the sounds Overcharge, over-discharge protection Sound Pressure: 120-130 db at 1 meter Frequency: 3-5 kHz With severe bird infestations, it is always recommended to use at least 2 bird control methods together. Sonic cannon is a very good to use in conjunction with the bio-acoustic bird repeller.

Optical encoders for defense and space applications: missile seekers weapon stations radar electro-optics systems space mechanisms (CMG, SADM, APM)

공중 통신용 VHF/UHF 트랜시버 제품군 R&S®M3AR 제품군의 소프트웨어 정의, 다중 대역 지원 공중 트랜시버는 모듈식 설계와 첨단 기술로 높은 MTBF 값과 긴 수명을 제공합니다. 작고 가벼운 이 트랜시버는 뛰어난 성능으로 무인 항공기를 포함한 모든 유형의 항공기에서 작동할 수 있습니다. 언제든지 다른 파형을 설치해 사용할 수 있어 다양한 작전 시나리오에서 상호 호환이 가능합니다.

MPS Microsystems offers a complete range of high precision ball screws for positioning less than 5 µm. Mostly custom-made, these screws ensure smooth and uniform movement resulting from the high precision of their thread, achieved by grinding. Our ball screws are made exclusively of stainless steel and are fitted with double nuts to allow fine adjustment of the axial play. Moreover, an optional ogival thread can provide a higher static and dynamic load capacity. Thanks to a large number of options, we can ensure that the ball screw meets your technical and quality needs. The following parameters can be personalized: lubricant (grease, oil, dry lubrication, no lubrication), customized screw ends, shape and external dimensions of the nut and screw, multiple nuts on the same screw, left-hand thread, thread length, specific axial play, special surface treatment, and more.