To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

It is a product produced in Korea and has high performance when used in EO/IR Gimbal for small drones. It can view both VIS and IR images simultaneously and is coupled to a small drone with a small weight to perform operations. Products with manufactured and domestic IR sensors in Korea. we deliver superior technologies that shape the future of defense. Whether supporting ISR missions or enhancing precision in loitering munition operations, MS60 products are designed to ensure operational excellence in the most challenging environments.

Potentiometers for aerospace applications: landing gears fly by wire fuel management system space mechanisms (SADM, robotic arms)

llumia ENGAGE facilitates open-ended training conversations using flexible AI agents to help practice 21st-century skills, decision-making and communication across multiple platforms.

ELECTROMECHANICAL RELAYS

Designed to support U.S. DoD modernization strategies, REDCOM Sigma is a complete software-based Command & Control solution with voice, video, chat, and conferencing. REDCOM Sigma® increases the warfighter’s operational flexibility while reducing size, weight, and power (SWaP) requirements at the tactical edge. REDCOM Sigma is based on open standards with a focus on interoperability, flexibility, and ease of use, and is listed on the DoDIN Approved Products List (APL). REDCOM Sigma was selected by the U.S. Army’s Program Executive Office Command, Control Communications-Tactical for network modernization at the tactical edge. Sigma is being deployed to multiple programs within the U.S. Army at the battalion level and below.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

Since the company was founded, Haynes International has played a key role in the development of the aerospace industry. During World War I, Haynes STELLITE® alloy cutting tools proved to be vital in meeting the increased production of military aircraft engines.