Lumir is the first Korean company to successfully develop and manufacture this onboard equipment, delivering superior performance and significant cost savings compared to competitors’ products. By integrating non-volatile NAND flash devices into the image data handling unit, storage capacity has been significantly increased, with data retention maintained even when the power is off.The image data handling unit of the satellite is a core device that receives high-speed, large-capacity data output from Earth observation sensors mounted on the satellite—such as SAR or optical cameras—then compresses and stores the data in real time, while also performing encryption and encoding for transmission to ground stations. Lumir has successfully developed and manufactured this satellite-mounted device domestically in Korea for the first time, breaking reliance on imported technologies. This achievement secures Lumir’s competitiveness by delivering superior performance and significant cost savings compared to foreign products.

Spring probes are designed to optimize performance in high reliability, multicycle applications. Smiths Interconnect’s spring probes are compliant which makes them ideal for blind mate applications as they self correct for x, y, z, rotational and angular misalignment of the target. Offered in compressed heights less than 2 mm and utilized on pitches as tight as 0.4 mm, they are well suited for high density, board-to-board, battery contact and high frequency applications. Mixed signals and functionality can be designed into a single connector.

Air conditioning units are designed for efficiency, durability, and environmental control, our units help ensure smooth ground handling and turnaround operations in all weather conditions Whether servicing commercial planes or private jets, our units deliver powerful and precise cooling and heating to ensure comfort for passengers and crew.

Leading edge high-speed opto-electronic modules, global communication needs made simple.

SAR satellites are designed for change detection and our unique Dwell, Spot, Strip and Scan modes give you the flexibility to monitor very large areas and zoom in to areas of interest at ultra-high resolution as needed. Get unprecedented visibility and flexibility with Dwell, Spot, Strip and Scan imaging modes. Monitor areas up to 50,000 km² and zoom in to areas of interest at very high resolution down to 50 cm – day, night and in any weather

The RFcore Radar series are FMCW type radar and were developed to detect/track small air targets. The major difference between three models is detection performance. RX32B is fundamental model. RX128B have four times larger radar than RX32B. RX192A have six times larger radar then RX32B. The number of the product name means the number of antenna elements. All have compact and lightweight physical architecture that concentrates all the components required for radar, such as antenna, RF components and radar signal processor, in a small single housing. Transport can be carried in the carrier box and can be easily carried by one person. For installation, you can use a commercially available camera tripod. The weight is about 7.5kg (RX32B) and 15.9kg (RX128B), and the lower connection part is compatible with the tripod connection for the camera. Power supply requires 12VDC (RX32B) and 24VDC power (RX128B and RX192A). When using a battery, it is possible to connect a 12V battery or 24V battery to radars. Usage time may vary depending on the battery capacity. RFCORE recommended the constant power supply. Transfer of Status and BIT information and simple control of the RX32B, RX128B and RX192A are possible with a web browser using the Ethernet connection for authorized users. Using the terminal program provided with the radar, you can view the radar control and detected target information in real time. All RX Radar series’ Power Amp and Core Chip were designed using RFcore's own products.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

InterGravity Technologies has developed a Type-III Composite Overwrapped Pressure Vessel (COPV) optimized for high-performance small spacecraft propulsion systems. The tank is designed with an aluminum alloy liner for impermeability and a carbon fiber/epoxy composite overwrap for high strength-to-weight ratio. The system is tailored for green propellant storage (C₂H₆, N₂O), offering an exceptionally lightweight yet robust solution for orbital transfer vehicles and CubeSat-class platforms. Technical Specifications - Type : Type-III COPV (Al liner + CFRP wrap) - Volume : 5.3 liters - MEOP : 75 bar - Proof : 230 bar - Burst : 250 bar - Dry Mass : < 1.0 kg