The SBC6511 Rugged Single Board Computer(SBC) from Abaco Systems features the new high performance, highly integrated Intel® Xeon® E processor (‘Coffee Lake Refresh’). Powered by Intel® Xeon® W processors, offering robust computational power. • Supports up to 64 GB DDR4 SDRAM with ECC and up to 256 GB (or in some variants up to 480 GB) NVMe SSD storage • Offers high-throughput networking: Dual 40 GbE data-plane (KR4 “fat pipes”) • Features the Xilinx® Zynq® UltraScale+™ MPSoC FPGA (ZU7EG) for enhanced security

The Crane stands as a state-of-the-art Mid-Wave Infrared (MWIR) detector. This device features a 5-megapixel resolution in a 2560×2048 format with a fine 5μm pitch. It is based on SCD's established XBn technology or Hot Full Midwave (HFM) and incorporates a digital readout circuit developed using an advanced CMOS process. The High Operating Temperature (HOT) Focal Plane Array (FPA) functions efficiently at 150K or 120K, enabling a large-format detector that excels in image quality while maintaining a relatively compact size, weight, and power consumption. SCD continues to lead in innovation.

Side shells, wing shells and fuselage structures are made of CFK, GFK, aluminium or organic sheets and get connected during production. Sealants are used to seal the connection surfaces. These are usually two-component polysulphides, which have to be applied in different geometries. Typical applications are: Fillet sealings, oversealings, interface sealings and seal caps. Due to their properties, polysulfides require very low pressure and shear handling. The compressibility of the fillers contained in the medium requires a high level of expertise and a coherent overall system from material removal to application. With manual application, long production times and high material ejection have a negative influence on the complete process. Complex quality standards are required due to the risk of human error. With the in-house developments of the vipro-DUOMIX from ViscoTec, this process can be depicted fully automatically. The individual nozzle design is also adapted to each application. The result is a controlled dosage in compliance with the specifications and at the same time the highest repeat accuracy.

Small wind power systems and component components Durability technologies: Composites - nacelle, blades, corrosion protection Stability technology: and wind speed control (electrical) + tail folding (mechanical) High-efficiency system: Direct-drive PMSG - slotless, blades, coefficient of power (Cp): 0.429 MPPT (Maximum Power Point Tracker) : Maximum power following control Web monitoring: Real-time monitoring Easy to maintain and install Quality Assurance: More than 3 years System certification: New and renewable energy facility certification, new product (NEP), excellent product designation by the Public Procurement Service - Korea's first Element parts certification: generator, inverter-CE, blade static load test, demonstration test completed Annual average wind speed of 4.5m/s or more

The sky’s the limit with the Bell 505. A high-tech flight deck and adaptable cabin design make it an extremely cost-competitive, and capable for any challenge.

EMCORE’s exclusive photonic integrated chip (PIC) technology delivers improved reliability and repeatability. The precision non-ITAR GEO-FOG 3D Dual features two GNSS antennas on a fixed PTK baseline to offer increased heading, pitch, and roll accuracy for static and dynamic applications where a single antenna system can be problematic. This dual antenna INS is the best choice for systems requiring heading at start-up or in low dynamic conditions. Highlights Data rate 10x faster than other available systems Cutting-edge sensor fusion for dependable, precise navigation in a full array of applications and conditions Six degrees of freedom (DoF) IMU with integrated gyros and accelerometers Technology Details Photonic Integrated Chip Technology EMCORE’s new photonic integrated chip (PIC) technology reimagines FOG technology by replacing individual fiber components with an innovative integrated planar optic chip. This results in a FOG with PIC Inside™ that’s even more reliable and delivers superior repeatability unit-to-unit. With three of these integrated photonic gyros at its core, the P-1750 IMU enables the GEO-FOG to provide the safe, accurate performance autonomous platforms demand. Learn More DSP Technology EMCORE’s DSP electronics improve FOG performance in critical areas such as scale factor and bias vs. temperature, scale factor linearity, and maximum input rate. EMCORE’s exclusive DSP design overcomes the limitations of analog signal processing, eliminating temperature-sensitive drift and rotation errors. GEO•FOG Manager The GEO•FOG Manager is ideal when integrating EMCORE’s GEO•FOG 3D and GEO•FOG 3D Dual INS. Learn More Developer’s Kit for Rapid Integration The KVH FOG/IMU Developer’s Kit includes easy-to-use software to accelerate your IMU and FOG integration, development, and interface efforts.

From precise control of various optical components(laser/detector/amplifier) & laser beam alignment(QD/FSM), a data rate of 10G can be achieved over distances of several thousand kilometers.

The Ophir® SupIR 80-1200mm MWIR f/5.5 and SupIR 60-1200mm MWIR f/4 lenses are designed for 15 µm 640x512 and SXGA 10 µm pitch FPA (focal plan arrays) cooled MWIR detectors, respectively, providing detection ranges exceeding 28 km. Key Features: - High performance IR continuous zoom lens - Compatibility with 10 µm SXGA/HD and 15 µm 640x512 cameras - Maintains accurate LOS & focus through the full zoom range - Designed for extended range observation & C-UAS systems - Detection range exceeds 26 km