It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

Lumir is the first Korean company to successfully develop and manufacture this onboard equipment, delivering superior performance and significant cost savings compared to competitors’ products. By integrating non-volatile NAND flash devices into the image data handling unit, storage capacity has been significantly increased, with data retention maintained even when the power is off.The image data handling unit of the satellite is a core device that receives high-speed, large-capacity data output from Earth observation sensors mounted on the satellite—such as SAR or optical cameras—then compresses and stores the data in real time, while also performing encryption and encoding for transmission to ground stations. Lumir has successfully developed and manufactured this satellite-mounted device domestically in Korea for the first time, breaking reliance on imported technologies. This achievement secures Lumir’s competitiveness by delivering superior performance and significant cost savings compared to foreign products.

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. L1/L5 Multi Constellation RTK GNSS The Certus Mini D supports L1/L5 dual frequencies, and GPS, GLONASS, Galileo, BeiDou and NavIC constellations. Access to multiple constellations and frequencies provides enhanced accuracy, availability and performance even in difficult environments such as multi-storey urban canyons. The GNSS receiver has 10 mm position accuracy with real-time RTK or post-processed PPK. Dual Antenna Heading The Certus Mini D provides a high accuracy heading solution using two GNSS antennas. The Certus Mini D rapidly and consistently maintains an accurate heading without the need for magnetic calibration and is unaffected by magnetic interference. Additionally, the system can determine heading while stationary. This makes it well-suited to applications where there is limited, or no, positional movement.

The APA-10 is a hybrid GPU equipped with diesel engine for continuous power and batteries for engine starting mode. Lightweight and maneuverable, the unit is perfect for indoor and outdoor use. Its relatively small size and extreme agility allow bringing the rectifier to any desired position. The elegant casing is made out of composite material, providing it long life and comfort to the user. The intuitive interface is user-friendly, making the GPU easy to control. Equipped with a highly durable chassis and mechanical braking system, this GPU is well prepared for heavy-duty and harsh conditions. The Ultra Green Power Solution Battery and Diesel engine driven GPU series APA is designed to reduce CO2 emissions with its unique technical characteristics.

Our products include latches, hinges, keepers and hold open rods.

This is the UAV launchers capable of launching the fixed-wing UAVs even on mountainous terrain, field, ships without sufficient runways to take off. It is designed to be the most powerful and easy to operate to take off the fixed-wing type UAVs of various specifications(Take-off weight, Take-off speed, and allowable G-force) into the air. It provides an interface that standardizes the shuttle for any type of unmanned aviation vehicle, and is easy to mount and to avoid take-off interference. A specially designed and manufactured hydraulic actuator is used to fully cope with the take-off weight of the aircraft, and a proprietary accumulator to allow a wide range of launch speed control. And multiple pulleys are equipped to ensure acceleration performance.

The Global Aerospace & Defense Team's Business Service Providers (BSP) Directory is designed to help U.S. aerospace and defense companies identify professional service providers to assist them in the assessment, completion, and/or financing of an export transaction.

The MIL-DTL-5015 series of connectors were developed as military standard connectors and applied to various military equipment, it is also used in general industries, medical care, electric vehicles, robots and automation facilities based on its high durability and reliability. This series is threaded coupling and the connection between the contact and the wire is based on soldering. It can be used compatibly with third-party products of the same standard since it is produced according to military standards.