Ring is a tactical point-protection solution against uncrewed threats. The full solution is comprised of 2 small components, with total weight of 27 kilos. The solution is battle-proven and designed for rugged exposure, either protecting forward base, tanks, armored vehicles, or light mounted forces. Ring uses standard 28v power and is extremely easy to use and deploy.

Electric motor used to drive the joint (WT axis) of the Explosive Ordnance Disposal (EOD) Robot.

Temperature Calibrated Pressure Sensors The Air Data Unit features very high accuracy absolute and differential pressure sensors. These are factory calibrated over a wide temperature range to further increase measurement accuracy and provide the best air data possible through varying conditions. Power Up Self-Calibration On top of factory temperature calibration, every time the air data unit powers up, it performs a self excitation calibration to adjust for small deviations of bias and scaling error. This allows the system to compensate for calibration aging and means that it never needs to be returned to the factory for recalibration. Reliability The Air Data Unit is built on top of a safety oriented real time operating system and all software is designed and tested to safety standards with fault tolerance. Its communication interface is optically isolated and the hardware is designed and tested to MIL spec.

HII ensures the flight readiness of aircraft worldwide, providing mission-critical test, weapon loading and hydraulic power generation equipment, parts and services for both military and commercial end markets.

1) Fabrication - possible Dismension : ~ D 1200 mm - Surface Errors PV < 79 nm RMS < 12 nm Roughness < 2 nm(Typical < 1nm) 2) Lightweight - lightweight Ratio : up to 82.5 % - Rib Thickness : ~ 2 mm - Face Sheet : ~ 7 mm - Lightweight Design & Fabrication

Our XR-based aircraft maintenance simulator is officially certified by the Ministry of Land, Infrastructure and Transport (MOLIT) of South Korea for training and education. It provides specialized training environments for the A321, B737-MAX, and B737-800NG aircraft, featuring over 80 detailed modules—including procedures for engine removal, main landing gear installation, and more. This subscription-based simulator is fully compatible with smartphones, tablets, and wearable XR devices, enabling seamless access through a cloud-based web service. Users can train anytime, anywhere—perfect for both remote learning and remote maintenance scenarios. Compared to traditional classroom learning, the XR platform is 4 times more effective and requires only one-third the training time. It also improves user confidence in real-world technical applications by up to 275%. By transforming traditional paper manuals into immersive, interactive training environments, the simulator delivers the next generation of aircraft MRO education for both civil and defense sectors.

The SBC3612D is a rugged 3U VPX single board computer aligned with the compute-intensive SOSA profile, delivering high-performance processing with the Intel® Xeon® D-2775TE 16-core processor and flexible expansion capabilities. • Supports up to 64GB DDR4 SDRAM and 480GB NAND Flash (NVMe SSD) • Offers 100GbE and 10/25GbE data plane and control plane support • Features the Xilinx® Zynq® UltraScale+™ MPSoC FPGA for enhanced security

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.