The SCXMC-SFPDP is a high-speed optical communication card that operates through the XMC interface of the SBC. It is designed to transmit and receive large volumes of data between the SBC and other devices in real time. Unlike Ethernet, which can be difficult to synchronize, the SCXMC-SFPDP uses optical communication with synchronization signals, enabling precise and high-speed data transfer. It offers low response latency (<40 µs) and supports four transmit/receive channels at 3.125 Gbps per channel. A device driver program is required for operation, and the Linux driver can be downloaded from Seedcore’s product page. Drivers for other operating systems can be developed upon request. This module is deployed in the L-SAM multi-function radar system to ensure reliable real-time data transmission between mission-critical subsystems.

Bell 429 - Arrive on the scene quickly, and be ready for anything. Ample cabin space, large doors and adjustable components accommodate your equipment --- and keep your crew comfortable.

Developed by MPS Microsystems, the voice-coil nano-positioner unites a Lorentz-force motor, flexure guidance and on-board electronics inside a 65 × 60 × 38 mm envelope. Standard travel is 2.88 mm, extendable to 7 mm with the same coil, suiting microscope objectives, small mirrors and sensors that demand friction-free motion. Bidirectional repeatability stays within ±1 µm over a 360 µm stroke and ±2.5 µm across the full stroke. We can tailor mounting plates, objective clamps and cable exits to suit your specific requirements, ensuring that this voice-voil actuator can be integrated seamlessly into your system.

To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

Type : Radial (3P) Size(Ø, mm) : 82 × 58 Weight(kg) : 0.55 N. Speed(rpm) : 6,200 N. Torque(Nm) : 2 N. Power(kW) : 1.3

Dual function pressure and temperature transducer

Next-generation satellite multi-band terminal system development project

- The 2nd generation mightyZAP series supporting dynamic speed & current control as well as position control along with position & current feedback - Built-in drive circuit, position sensor, 12mm diameter coreless DC motor and gear box - 27/40/53/90mm stroke option - Rated Load of 12N ~ 100N according to gear ratio for each stroke (Speed is inversely proportional to Rated Load, so the stronger the Rated Load, the slower the speed.) -Support RS-485 or TTL / PWM communication * TTL / PWM communication version operates by automatically recognizing the input TTL / PWM signal * When using PWM communication, only the position command is available without position feedback (For feedback feature, use TTL or RS-485 communication) Both MODBUS RTU and IR open protocols available (Default : IR Open protocol)