In order to guarantee the quality requested by customer, we have been implementing thorough quality control based on ISO9001, ISO14001, TSI6949, the National Defense Quality Management System and SQ processor.

High Power Polarizing Beamsplitter Cube coatings are deposited on the hypotenuse of right angle prisms that are optically contacted. They are designed to separate an incident beam into its S and P polarization components with an average extinction ratio (TP/TS) in excess of 500 : 1. The incident energy is split into two orthogonally polarized beams that emerge at 90。with respect to each other. These coatings were developed specifically for use in high power pulsed and CW laser applications.

To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

Ultra-High Accuracy MEMS Certus Evo features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Certus Evo’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Certus Evo is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. AI-Based Algorithm Certus Evo features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. Dual Antenna RTK GNSS Certus Evo contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus Evo contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi Protocol Support Certus Evo features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

K2 online mall

To reduce aircraft development lead-time, Safran Engineering Services is specialized in quick design and engineering in full autonomy. Teams provide global loads for ground and flight maneuvers, follows the evolution of weight and center of gravity for aircraft components and support sales campaigns with weight & balance evaluation.

The Monitor meets the military environmental specifications. COTS technology's design, manufacturing and technical support is committed to continuously providing a total solution to your display needs. The Monitor uses a full array of LED backlights which employ a local dimming technology for precise picture control and smooth motion for a more natural picture.

FINISHED THE DEVELOPING / INTEGRATED THE 2CH. FORJ Specification MODEL: SREM-1466-012 APPLICATION: SONAR WINCH SIZE: Φ140(O.D) / 664(H) NO. OF RINGS: 128RINGS TYPE: END ROTATING: CW/CCW