aviation fuel refueling cart : Mobile refueling cart that can easily refuel light aircraft and helicopters Sump recovery system : Collect the drained/sumped aviation fuel from the aviation fuel refueling system, easily sample and test it, and then decide whether to drain it or return it to the system. Aviation fuel refueling system : The aviation fuel refueling system is compactly constructed with a skid for easy use and installation.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Giraffe 1X is an ideal air surveillance component in the Ground Based Air Defence (GBAD) domain that provides ground based air defence commanders with engagement quality target data, drone detection and Counter-Artillery, Rocket and Mortar (C-RAM) sense and warn within a single solution. It is the ideal main sensor for a Very Short Range Radar (VSHORAD) system and can be used as a gap filler that complements larger GBAD systems, or as a Counter-UAS (C-UAS) solution.

The KX1-3046 is an X-band high-power MMIC amplifier fabricated on the GaN-on-SiC process. It operates from 8.0 – 10.5 GHz and typically provides 30W saturated output power with power-added efficiency of 46%. The KX1-3046 can support military and commercial radar systems. It is matched to 50Ω with integrated DC blocking capacitors on both RF input and output ports. The KX1-3046 is 100% DC and RF tested on-wafer. It is available in chip form. **Key Features** - Frequency Range: 8.0-10.5GHz - Small Signal Gain: 28dB - High Pout: 30W - High PAE: 46% - DC bias: Vd=28V @Idq=0.6A - Pulsed Vg: PW=100µs, DC=10% - Chip size: 2.95x3.1x0.1mm  

From parts supply to total logistics support, GE has the right program to support your maintenance needs -- and keep more of your assets in their theater of operation. Our extensive maintenance management experience can maximize your engine and parts availability by improving procurement lead time and boosting shop productivity.

The N Series of mini modular, high density connectors offers a variety of combinations in a single connector frame. It employs a do-it-yourself system based on the building block principle, which allows users to select the connector design that meets their specific requirements through off-the-shelf components.

Our software enables engineers to analyze and optimize their preliminary designs in the best way possible – at the whole aircraft level – which not only saves time but money as well. With its Multi-disciplinary Analysis and Optimization (MDAO) approach, you can model aircraft and their subsystems, assess performance, and generally accelerate your progress in numerous design challenges. Whatever your aircraft preliminary design goals may be, Desmo has a solution.

TESCAN SOLARIS X 2 extends FIB physical failure analysis capabilities to large-area applications, making deep cross-sectioning of advanced packaging devices, displays, MEMS, and optoelectronic devices more efficient. Featuring the new generation Mistral™ Xe Plasma FIB column, SOLARIS X 2 offers increased maximum ion beam current and a sharper ion beam profile across the full range, with significantly reduced beam tails. This allows operators to use higher milling and polishing currents, achieving superior surface quality comparable to conventional Plasma FIB, but with greater speed and precision.