Interconnect Wire Harness and Cable Assemblies are the connectivity backbone of electronic systems. Fabricated in a factory setting, build-to-print wire harness assemblies enable the OEM manufacturer to reduce the time and expense of in situ interconnection of electronic devices used in complex air, sea, land and space applications.

The SC-SBCRTM-V2 is a Rear Transition Module (RTM) designed to extend the I/O functionality of the SBC6511 single-board computer. Mounted on the rear side of the main VPX backplane, this module provides additional I/O expansion through Micro-D and D-sub connectors for synchronization signals, two Ethernet ports, two Mini-DisplayPort video outputs, two USB interfaces, and MMCX connectors. It enhances system flexibility and connectivity for embedded and radar signal-processing applications.

MDCX, multipin coax connectors, offer low VSWR of 1.25:1 (typ) up to 10 GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, with constant 50 Ohm airline impedance. MDCX coaxial contacts are compact in size allowing multiple high density connections in a Micro-D style shell for applications where space and weight savings are important. No cumbersome spring mounts are required. These connectors are also available with locking post mechanisms or blindmate hardware attachment.

This plays an important role that connects EMI shielding pieces of connectors and cables when manufacturing EMI shielded cables. It is also applied and used in defense, space, aviation, and industrial equipment. Key features of the military connector adapter: Designed to be compatible with various MS/VG standard connectors and general connectors. Environmental Protection: It is waterproof and dustproof, ensuring stable operation in severe weather and extreme environments. Robustness: It is highly durable against impact, vibration, corrosion, and more to meet military and industrial requirements. EMI shield: Prevent electromagnetic interference (EMI) to maintain signal integrity.

The MD250MW is a 15mm, metal gear, mini servo with dual ball bearings and a cored motor with carbon brushes. Engineered with a programmable digital amplifier and magnetic encoder to deliver high performance and reliability for remote, unmanned aerial vehicles and ground-based automation applications. Operating via DroneCAN (formerly UAVCAN) command protocol at a wide voltage range from 4.8~7.4 volts, this compact actuator produces impressive torque and high speeds in its mini class. The MD250MW servo is ideal for a variety of applications requiring an efficient balance of performance and cost. #UAV #UAS #UGV

AI Navigation Algorithm Certus features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS Certus contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Dual Antenna RTK GNSS Certus contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi-Protocol Support Certus features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

Decontaminated and / or sterilized gloves PIERCAN has offered its customers decontaminated and/or sterilised gloves. This service is intended in particular for pharmacy environments (pharmaceutical laboratories, hospitals etc.) but it may also be for industries in which an extremely high level of cleanliness is now absolutely vital (space, military, research etc.).

DS Aether CT provides various industrial Gas Tube Trailers such as Helium (He), Hydrogen (H2), Neon (Ne), Nitrogen (N2) and Argon (Ar), as well as CNG. The working pressure is set to national requirements or customer's demands such as 166 bar, 200 bar, or 250 bar. The color of the jumbo tubes and skid frames follows ISO color codes, or the designations of customers.