The JW22992 connector was developed for the purpose of high-power transmission with demanding military standards and exhibits IP67-grade water and dust resistance. It is also designed in the range of 40 to 200 amps and is used for high-power military and industrial equipment that requires the highest reliability. Key Features: High Power Transmission, Designed to handle high currents, Robust construction It provides a stable connection with five key grooves and two-line screws.

BlackThorn™ is a family of mission-configurable warheads, built around the mission rather than the platform. From a common architecture, customers can match the right effect to each target, integrating the capability across missiles, autonomous systems, one-way effectors, counter-uncrewed aerial systems (C-UAS) and uncrewed ground vehicles. Common interfaces allow for rapid integration, and the architecture can evolve as threats and platforms change. 

A device that filters outside air through a filter of a positive pressure device during chemical warfare

The maximum transmission distance varies based on the following frequency-related specifications. Camera Frequency Max Cable Length ================ =============== 20 ~ 60 MHz 10 m 60 ~ 80 MHz 7 m 80 ~ 85 MHz 5 m  In cases where a single PC cannot handle large amounts of image data, it becomes necessary to duplicate the image and use multiple PCs for processing. A splitter is required in such scenarios.  The CLS-30T2S amplifies and transmits image signals from a single camera to up to two PCs, supporting Base/Medium/Full configurations (10 Taps supported).  The Master side transmits RS232 and CC1~4 signals, while the Slave side replicates and transmits image signals only.

Rolatube IAM (Integrated Antenna Mast) is a lightweight, man-portable communications mast that integrates a high-efficiency dipole antenna directly into its structure—redefining rapid tactical deployment. Built from Rolatube’s proprietary bistable composite, the IAM unrolls to full height without tools, enabling users to connect and transmit in seconds. Available in 3.5 m and 7 m models, the mast weighs just 1.9 kg and packs down to a 150 mm roll, offering unmatched portability for dismounted operations. Designed for reliable RF performance, the IAM ensures no signal loss when in contact with grounded surfaces. Its embedded omni-directional dipole antenna delivers superior range and VOR communication performance compared to traditional systems. The 3.5 m IAM comes in VHF (30–300 MHz) and UHF (136–470 MHz) variants, each available in four colours, with a top-cap socket for L-Band antenna integration, extending the system’s use to applications such as telemetry, GPS, and aircraft surveillance. The mast can be handheld, guyed, or elevated via an integrated rigging point, and is engineered to meet MIL-STD-810G, fully maintenance-free, and resistant to water, dust, and UV. With a wind rating of 100 km/h (62 mph) when guyed, the IAM stands up to demanding field environments while delivering high-performance, elevated communications infrastructure at the tactical edge.

ㅇKey Features RF Front-End - Frequency : C-Band - Tx Power : +27 dBm(0.5 W) , Rx Range : -10 ∼ -100 dBm - Rx Sensitivity : -95 dBm@2 MHz Baseband & Modem - Downlink : 2.4 Mbps / Uplink: 8 kbps - QPSK waveform and CTC Forward Error Correction Anti-Jamming / Anti-Spoofing / Video CODEC - Anti-Jamming Capability using DSSS - Anti-Spoofing Capability by AES-256/ ARIA-256 Encryption - Support H.264 / up to 1920x1080x30f Interface - 10/100 Base-T Ethernet x1, RS-422 x1, RS-232 x2 - 3G-SDI Digital Video IN/OUT Interface - Limited Discrete I/O (1PPS/sync_in, reset_in, status_out) ㅇQuality and Certification - MIL-STD-810G - MIL-STD-461F

The SWIFT-EI is the world’s first SWIR detector to feature a state-of-the-art read-out integrated circuit (ROIC), enabling low size, weight, power, and cost (SWaP-C). It supports VGA image format for SWIR imaging, multi-spot ALPD (asynchronous laser pulse detection), and a rapid imaging frame rate of up to 1,600 frames per second. The revolutionary ROIC introduces an independent neuromorphic imaging stream for event detection, which greatly expands capabilities in target detection and classification. Ideal for cutting-edge, low SWaP-C applications, the SWIFT-EI can be integrated into a variety of air platforms, missiles, vehicles, and handheld devices, making it extraordinarily versatile. With SWIFT-EI, SCD’s customers always have the advantage of being the FIRST TO SEE.

The AMT-206-1 composite tail rotor blade is a direct replacement for Bell 206A and 206B series helicopter tail rotor blades. Now fitted with a new style of feathering bearings manufactured by KAMATICS. These bearings provide a longer life expectancy, with a patented lining that provides lighter pedal loads and a higher level of chemical resistance, compared to that of the standard fabric Teflon-lined bearings. The AMT-206-1 tail rotor blade has a non-symmetrical airfoil section and incorporates a swept tip. The T/R Blade is primarily fabricated from uni-directional Graphite (carbon fiber) and Aramid (Kevlar™) continuous fibers suspended in an epoxy matrix and is fitted with a nickel abrasion strip on the leading edge. The abrasion strip is bonded on using a urethane adhesive. The AMT-206-1 composite tail rotor blades have a 30% cost advantage, twice the lifespan, higher strength and thrust, and a substantial noise reduction, making them safer and ideal for helicopter operators flying in noise-sensitive areas like national parks and built-up areas.