Versatile, high density 4 contact row connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification. With a 0.6mm contact diameter, CMD connectors are available from 42 to 316 contact positions with dip solder and SMT soldering contact termination types.

To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

The 100W High Power Amplifier is an L-band amplifier that delivers 100W output across two channels with a 60% duty cycle. It offers a gain of over 50 dB, with output flatness of 2 dB depending on the input signal level. The amplifier provides an ACLR performance of -20 dBc at maximum output. Equipped with an output-stage bandpass filter (BPF), it achieves excellent harmonic suppression of -70 dBc. Built-in monitoring functions include output signal and temperature monitoring.

Specialty Tool Kits and Custom Sheet Metal Kits

Ultra-High Accuracy MEMS Motus features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Motus’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Motus is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. Miniature Package Never before has such high inertial performance been available in such a small package. Motus consumes just over 1 cubic inch in volume and weighs only 26 grams. This makes it ideal for weight and size sensitive applications. Motus is available in an OEM package suitable for integration into larger products or an enclosed package for external and standalone use. Advanced Signal Processing Motus samples its sensors synchronously at 1000Hz through six individual 24-bit differential ADCs which minimizes noise as well as providing optimal thermal calibration and performance characteristics. 14 separate heavily filtered regulated power supplies ensure that each sensor and ADC is operating off the cleanest possible power supply. Reliability Motus has been designed from the ground up for mission critical control applications where reliability is very important. It is built on top of a safety oriented real time operating system and all software is designed and tested to safety standards with fault tolerance in mind. The hardware is designed and manufactured to mil standards. High Update Rate Motus outputs temperature calibrated sensor data at 1000Hz as well as filtered attitude at the same rate. This allows for control of dynamically unstable platforms.

- The 2nd generation mightyZAP series supporting dynamic speed & current control as well as position control along with position & current feedback - Built-in drive circuit, position sensor, 12mm diameter coreless DC motor and gear box - 27/40/53/90mm stroke option - Rated Load of 12N ~ 100N according to gear ratio for each stroke (Speed is inversely proportional to Rated Load, so the stronger the Rated Load, the slower the speed.) -Support RS-485 or TTL / PWM communication * TTL / PWM communication version operates by automatically recognizing the input TTL / PWM signal * When using PWM communication, only the position command is available without position feedback (For feedback feature, use TTL or RS-485 communication) Both MODBUS RTU and IR open protocols available (Default : IR Open protocol)

The APA-10 is a hybrid GPU equipped with diesel engine for continuous power and batteries for engine starting mode. Lightweight and maneuverable, the unit is perfect for indoor and outdoor use. Its relatively small size and extreme agility allow bringing the rectifier to any desired position. The elegant casing is made out of composite material, providing it long life and comfort to the user. The intuitive interface is user-friendly, making the GPU easy to control. Equipped with a highly durable chassis and mechanical braking system, this GPU is well prepared for heavy-duty and harsh conditions. The Ultra Green Power Solution Battery and Diesel engine driven GPU series APA is designed to reduce CO2 emissions with its unique technical characteristics.

The beginning of the mission given to ammunition The mission of all ammunition begins with the fuse. We are developing and mass-producing fuses based on our many years of experience in developing and mass-producing various fuses to meet the needs of users, including electronic timed fuses, mechanical fuses, and training fuses. Completion of mission given to ammunition Warheads such as penetrating warheads for penetrating power, thermobaric warheads using thermal pressure, and dispersion warheads for suppressing local targets play the role of completing the final mission of the ammunition. Korea Defense Industry has many years of experience developing and mass producing such warheads.