STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

The Haigh-Farr Wraparound™ is a self-contained omnidirectional antenna for cylindrical or conical shaped bodies. A single point feed is used and no external splitters, combiners or cable harnesses are required for installation. The antenna is conformal, and may be mounted flush, or on the exterior of the vehicle. Designs are available from 300 MHz to 13 GHz with typical applications including Flight Termination, GPS, Telemetry, Data Links and Transponder. Multiple antenna elements may be combined within the same physical Wraparound™, providing multi- band capability in a single, compact package. Wraparound™ antennas have been flown on vehicles from subsurface sea to space, including high-mach kinetic kill weapons, high-G projectiles and re-entry vehicles. The Wraparound™ has been qualified for use on several high performance vehicles flown on test and launch ranges throughout the United States and Europe. For high aero-heating applications an ablative heat shield may be added to the antenna for additional thermal protection.

Presentation by Haigh Farr during the Virtual NH Career Fair, hosted by JobsInNH.

We carry a wide range of aerospace-grade materials in round bar and sheet, including: -Alloy 718 (AMS5596) -Alloy 625 (AMS5599) -Alloy X (AMS5536) There is no minimum order quantity ? we can cut from a single piece and ship within 1?2 days, complete with full material traceability. For non-stock grades, shapes, and standards, we can source materials from suppliers worldwide with a lead time of approximately 2 weeks, also with no minimum order quantity.

- An updated model of the Heron UAV Strategic and versatile aircraft capable of carrying diverse payloads - Can reach an altitude of 35,000 feet, speed of 150 knots and remain in the air for 45 consecutive hours - Wide and strong body structure, allowing for quick and easy maintenance without adding to its weight - Enables new configurations, as long-range observation sensors and radars

SAF-FIRES™ is a standards-based, image generator agnostic, and scalable Call-For-Fire and Close Air Support training simulation with autonomous Smart Trainer suitable for deployment in Joint Fires and accreditable JTAC training simulators. Built upon the same Call-For-Fire and Close Air Support software engine that powers the accredited simulation Fires FST™, SAF-FIRESTM delivers the same mature and complete Joint Fires training solution but makes it available for integration with any DIS, HLA or CIGI compatible simulation or Image Generator. Supporting both conventional near-peer and counter-insurgency operational scenarios, SAF-FIRES™ enables JFOs and JTACs to train realistically in a modern complex battlespace against an agile and adaptive adversary. Heightened realism and cognitively challenging training are enabled through the incorporation of non-combatants, urban clutter, UAV surveillance, various close air support platforms and accurate military targeting procedures.

• Openable sleeves • Expandable sleeves • Convoluted conduits • Heat shrink tubing & sleeves • Heats shrink boots • Specific sleeves

1. Machining • Small, medium, and long bed machining available, with sizes up to 20 meters • Precision 5-axis machinery supporting 4m, 6m, 8m, and 20m machining beds. • Capable of machining both hard and soft metals 2. Sheet Metal Fabrication • Roll forming (11m), skin stretch forming (10m) • Bladder and stretch wrap forming • Skin milling & NC routing 3. Composite • Specialized Curing Oven up to 15M • Layup Facility 4. In-house Heat Treatment Facility (NADCAP Accredited) Highlights √ Proven Korea Defense Offset Partner for Global OEM √ Integrated Global Program Operation in Korea and USA Facilities √ Boeing & Lockheed Martin Award Winning Supplier Project Highlight : • A32X/A330 Skin Structure, Floorgrid, Doors • KT-100 Full aircraft Integration • Helicopter Fuselage, Torque Box, Bulkhead, Leading Edge etc.