Sponsored] Raytheon Missiles & Defense, a business of the newly formed Raytheon Technologies, is built on a foundation of advanced innovation and excellence...

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

The SDT F 16 Combat Training Pod is mounted on F-16 and similar air platforms in an external pod, and ensures efficiency in exercises and in the provision of air-to-air and air-to-ground tactics training to pilots. SDT F - 16 Combat Training Pod features advanced air-to-air and air-to-ground combat training capabilities, such as real-time autonomous position generation, weapon simulation and real-time hit/miss notification, thanks to its long-range and high-speed RF data link and integrated processors. The system has mission planning, live monitoring, debriefing and analysis/evaluation features. The SDT F 16 Combat Training Pod enables training in real flight conditions and in multi-threat/target environments. Its high-speed data link and modular design mean that the System is also a Live-Virtual-Constructive (LVC) training infrastructure.

Counter-Drone System Planning & Optimization, Quantitative, Objective-Based Operational Performance Analysis & Management for Critical and Contested Areas

EpiShuttle is all about protecting both patients and health care professionals. The EpiShuttle is an isolation unit designed for quick and easy transport of highly infectious and vulnerable patients.

The PANDION Q450 is a modular drone that allows users to swap out its detachable D-ARK module pack, enabling flexible configurations of cameras and internal PCBs. As the drone industry diversifies, users can select purpose-specific module packs, allowing a single product to meet various consumer needs with multiple configurations. The D-ARK module pack integrates the camera, flight controller (FC), and all circuitry, allowing users to upgrade, modify specifications, or perform maintenance simply by swapping the module. Designed to offer an optimized configuration for a wide range of users, this modular system provides a cost-effective solution tailored to diverse needs in the drone industry. PANDION Q450 has a solid design with water and dust resistance for rugged environments.

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.