To guarantee maximum safety and reliability, our DA 30 features a brushless motor and a contactless wear-free position sensor. This means maximum service life with the greatest‐possible power delivery and its design prevents electromagnetic emissions (EMI) caused by brush sparking. The housing made of saltwater‐resistant aluminum is HART‐coat treated, meets the IP‐67 standard for water and dust sealing and provides an integrated Sub‐D connector (MIL spec. circular connector or cable gland on request). Brackets integrated in the housing for horizontal and vertical assembly. 8‐fold, ball‐bearing supported, steel gear train, drive shaft with ANSI multi‐tooth. The DA 30 series can be equipped with a standard PWM input (Pulse Width Modulation) that has two different interfaces: a differential, galvanic isolated interface (Opto‐Coupler) and a single‐ended interface with CMOS levels that is also used to program the servo parameters. It includes analog position feedback to detect the drive shaft position. A differential RS‐422 PWM interface can be chosen instead of the opto‐coupled interface. The DA 30 with digital serial command interface (RS‐485) receives its commands via a CRC secured protocol. It can return not only the shaft position in digital format, but also several diagnostic data such as the level of the supply voltage, current consumption and the temperature of the motor and electronics in digital form (optionally also the humidity within the actuator case). These kind of diagnostic capabilities help to determine the health state of the actuators before, during and after deployment.

The SDT F 16 Combat Training Pod is mounted on F-16 and similar air platforms in an external pod, and ensures efficiency in exercises and in the provision of air-to-air and air-to-ground tactics training to pilots. SDT F - 16 Combat Training Pod features advanced air-to-air and air-to-ground combat training capabilities, such as real-time autonomous position generation, weapon simulation and real-time hit/miss notification, thanks to its long-range and high-speed RF data link and integrated processors. The system has mission planning, live monitoring, debriefing and analysis/evaluation features. The SDT F 16 Combat Training Pod enables training in real flight conditions and in multi-threat/target environments. Its high-speed data link and modular design mean that the System is also a Live-Virtual-Constructive (LVC) training infrastructure.

Raytheon Intelligence & Space's ISTAR is a multi-intelligence aircraft that uses artificial intelligence, integrated onboard sensors and advanced processing to provide critical information to military and civilian air and ground crews. Our integrated suite of ISR solutions provide state-of-the-art capabilities for national defense missions.

The ACTUS® Laser Boresight is a precision device mounted directly onto the gun barrel, accurately indicating the exact aiming position of the muzzle. With a divergence angle of less than 0.6 mrad, it provides exceptional accuracy, making it an essential tool for precise alignment and target acquisition. The circular laser beam, with a 7.5 cm diameter, is visible to the naked eye from distances of up to 125 meters. The laser output is easily adjustable, offering versatility for use in various environments. Engineered for easy attachment to the gun barrel without causing any damage, the ACTUS® Laser Boresight also includes a remote harness for convenient operation from up to 4 meters away. Supporting 100-240V AC voltage, it ensures stable operation and excellent compatibility worldwide.

Features Solid-state, maintenance-free, modular components for optimal mounting of controls, sensor, and display Automatic compensation ensures the highest degree of accuracy (±1º) LCD display with adjustable backlighting for easy viewing in all conditions Variable control of electronic damping for use in rough seas Meets demanding military standards for years of reliable performance Dual compensation for degaussing on and off Applications Naval vessels including aircraft carriers, battleships Smaller naval boats Amphibious craft

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. L1/L5 Multi Constellation RTK GNSS The Certus Mini D supports L1/L5 dual frequencies, and GPS, GLONASS, Galileo, BeiDou and NavIC constellations. Access to multiple constellations and frequencies provides enhanced accuracy, availability and performance even in difficult environments such as multi-storey urban canyons. The GNSS receiver has 10 mm position accuracy with real-time RTK or post-processed PPK. Dual Antenna Heading The Certus Mini D provides a high accuracy heading solution using two GNSS antennas. The Certus Mini D rapidly and consistently maintains an accurate heading without the need for magnetic calibration and is unaffected by magnetic interference. Additionally, the system can determine heading while stationary. This makes it well-suited to applications where there is limited, or no, positional movement.

ZYXCAD is a high-performance CAD software developed by ZYX Technology, offering full compatibility with DWG files and optimized for speed, stability, and usability. It is designed for professionals in architecture, engineering, construction, manufacturing, and defense who require precise and efficient drafting tools. With support for multi-core CPU processing and memory optimization, ZYXCAD ensures smooth operation even when working with large-scale drawings or on long, complex projects. Its fast load times, intuitive interface, and powerful engine allow users to focus on design without interruptions. A key advantage of ZYXCAD is its flexible licensing system. While many CAD platforms are available only as annual subscriptions, ZYXCAD offers both rental and perpetual licenses, giving users more freedom to choose the option that best fits their business needs and budget. The PRO version of ZYXCAD comes bundled with WORKS, a powerful suite of over 450 built-in productivity tools. These tools enhance drafting efficiency by automating repetitive tasks such as block insertion, layer management, dimensioning, and batch editing. With WORKS, even complex tasks become faster and easier, reducing errors and improving project turnaround times. ZYXCAD also supports various file formats beyond DWG, including DXF, DWF, DGN, PDF, STEP, and IFC, ensuring seamless collaboration and compatibility in diverse work environments. As a trusted CAD solution used by government agencies, universities, businesses, and defense-related institutions, ZYXCAD continues to grow as a competitive and reliable alternative to expensive legacy CAD systems. It combines professional-grade performance with cost-effectiveness, making it ideal for teams seeking to modernize their design workflows without compromising quality or functionality. Whether you are transitioning from other CAD platforms or looking for a better way to manage your design tasks, ZYXCAD offers the tools, speed, and flexibility to help your organization succeed in today’s fast-moving digital landscape.

1. Maintenance • Depot Maintenance • Structure & Avionics Replacement, Repair, Wire Harness, Test and Inspection 2. Upgrade & Modification • Structure Upgrade and Modification • Avionics Upgrade, System Integration, Test and Inspection Highlights √ Final Assembly incl. Engine Installation √ System Integration, Test & Inspection Project Highlight : KT-100 & Light Sport Aircraft (Final Assembly), HH-60, CH-53, CH-47, F-16, P3-c, C-130H, AS-1S, MD500, NG RQ-4B ( Logistic & Ground Support)