The SWE550S is a rugged 6U VPX fully managed Layer-2/3 Ethernet switch aligned with the SOSA profile, providing blazing-fast 25/100 GbE switching via a 3.2 Tbps fabric and flexible I/O reconfiguration. • 3.2 Tbps switch fabric delivering full wire-speed bandwidth (~2.5× typical) • Front: up to 2×100 GBASE-SR4 (MPO); Rear: up to 7×100 GBASE-SR4, SWE540A-compatible I/O • Fat-pipe ports reconfigurable into thin-pipe ports; copper ports support 25/100→10/40 Gb speed downgrade • Dual-core ARM + OpenWare™ management; built-in storage sanitization • SOSA-aligned 6U VPX form factor; air & conduction cooled; rugged Levels 1, C, E

- The 2nd generation mightyZAP series supporting dynamic speed & current control as well as position control along with position & current feedback - Built-in drive circuit, position sensor, 12mm diameter coreless DC motor and gear box - 27/40/53/90mm stroke option - Rated Load of 12N ~ 100N according to gear ratio for each stroke (Speed is inversely proportional to Rated Load, so the stronger the Rated Load, the slower the speed.) -Support RS-485 or TTL / PWM communication * TTL / PWM communication version operates by automatically recognizing the input TTL / PWM signal * When using PWM communication, only the position command is available without position feedback (For feedback feature, use TTL or RS-485 communication) Both MODBUS RTU and IR open protocols available (Default : IR Open protocol)

ㅇKey Features - Low Dielectric Permittivity / Low Weight / Low Cost - Possible Customization - Operating Temperature : -40℃∼ +900℃ - Random Vibration : 6.1Grms , 20 Hz to 2000 Hz, 3 axis - Shock : 20 G (Minimum Peak) Sawtooth , 3 axis - Altitude : Up to 160,000 ft (0.929 mbar) ㅇQuality and Certification - MIL-STD-810G

Kia developed Granbird Bare Chassis Vehicle based on long-accumulated technology and infrastructure for commercial vehicles. This Granbird Bare Chassis vehicle can be easily modified as specialized vehicles on the basis of diverse customer requirements.

Electric motor used to drive the joint (WT axis) of the Explosive Ordnance Disposal (EOD) Robot.

Supported by a rugged internal combustion engine compatible with heavy fuels, Reliant delivers over 10 hours of persistent ISR without runways, launchers, or recovery gear. Designed for high-wind, high-altitude, and denied environments, Reliant excels where legacy platforms fall short. Dual swappable payload bays support ISR, SIGINT, or EW missions, while onboard edge AI processing enabled by NVIDIA Jetson Orin NX modules delivers real-time threat detection and adaptive rerouting, even without connectivity. The platform can be deployed by a two-person team in under 10 minutes using a compact 10×10-meter footprint for launch and recovery from rooftops, vehicles, ships, or remote terrain. With an IP55-rated, all-weather design and reliable GNSS-denied navigation, Reliant gives operators the flexibility and resilience required to operate in complex, contested battlespaces.

The AMT-206-1 composite tail rotor blade is a direct replacement for Bell 206A and 206B series helicopter tail rotor blades. Now fitted with a new style of feathering bearings manufactured by KAMATICS. These bearings provide a longer life expectancy, with a patented lining that provides lighter pedal loads and a higher level of chemical resistance, compared to that of the standard fabric Teflon-lined bearings. The AMT-206-1 tail rotor blade has a non-symmetrical airfoil section and incorporates a swept tip. The T/R Blade is primarily fabricated from uni-directional Graphite (carbon fiber) and Aramid (Kevlar™) continuous fibers suspended in an epoxy matrix and is fitted with a nickel abrasion strip on the leading edge. The abrasion strip is bonded on using a urethane adhesive. The AMT-206-1 composite tail rotor blades have a 30% cost advantage, twice the lifespan, higher strength and thrust, and a substantial noise reduction, making them safer and ideal for helicopter operators flying in noise-sensitive areas like national parks and built-up areas.

Interconnect Wire Harness and Cable Assemblies are the connectivity backbone of electronic systems. Fabricated in a factory setting, build-to-print wire harness assemblies enable the OEM manufacturer to reduce the time and expense of in situ interconnection of electronic devices used in complex air, sea, land and space applications.