Manufacture and delivery of main-part reflectors used in unmanned aerial vehicles.

AI Navigation Algorithm Certus features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS Certus contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Dual Antenna RTK GNSS Certus contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi-Protocol Support Certus features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

HDB0800SG is a HUD (Head Up Display) Repeater installed in fixed wing of Korean Air Force, which shows video information given from the cockpit HUD to the rear seat.

Duratek’s motor drive power supply is engineered to absorb excess energy during motor regeneration and braking phases, ensuring consistent and stable voltage delivery.

Altimeter for Missile Application

The Improved Fire Control System (IFCS) PNU / Universal Fire Control System (UFCS) UPNU family represents a true state-of-the-art system approach. Its design features permit ready adaptation and/or optimization to any current or future weapon system or sensor requiring precision pointing and positioning. The PNU / UPNU and its variants point the way for the future direction of the land navigation systems. Utilizing advanced sensors, electronics, software and aiding (GPS and odometer), the PNU / UPNU family delivers precisely what the Army of tomorrow needs — a system designed to remain operationally effective and affordable to support well into the future. Features High-performance RLG-34 ring laser gyros Common architecture and components (Paladin, PIM, Firefinder, IPADS) Embedded 12-channel Selective Availability Anti-Spoofing Module (SAASM) Impervious to jamming (inertial mode) Resistant to jamming (GPS-aided mode) Combat-proven Embedded Built-In Test (BIT) High reliability MTBF, low mean time to repair (MTTR) No periodic calibration required Applications Multiple Launch Rocket System (MLRS) High-Mobility Artillery Rocket System (HIMARS) Pointing and position location

SBC (single board computer) for VMEbus based on TI DaVinci CPU, ARM Cortex-A8 1.2GHz, C674x 1GHz DSP, SGX530 3D Graphics Engine, DDR3 memory, Giga Ethernet 2 port, video input/output 5 port, SATA-2 2.5" SDD This is a built-in SBC board for video processing. Application field: image processing system Shipboard EO video system Video encoder/decoder system Multi-channel video storage/distribution system Characteristic: VME type multi-channel video recorder Supports 4-channel NTSC/PAL video compression (H.264) Supports 4-channel audio recording Supports local video and audio playback Supports network RTSP function Supports Ethernet-based GUI control

The SC-SSGMRTM, a Seedcore Co., Ltd representative product, is a backplane transmission module that performs the I/O function of the SSGM(Synchronous Signal Generation Module). When the SSGM(Synchronous Signal Generation Module) board is plugged into the motherboard(Backplane) in front of the Chassis, you can extend the I/O function of the board by plugging the SC-SSGMRTM board into the back of the Backplane. Three 37-pin Micro D-sub ports are used to send synchronization signals generated by SC-SSGM to the outside or to receive external synchronization signals, Three separate MMCX output ports are prepared to support test equipment such as oscilloscopes, and you can convert them to various signals and output them.