With an AS9120-certified logistics system and strong semiconductor expertise, we are tailored to support defense and aerospace customers, where small-volume, high-mix requirements, long life cycles, and unpredictable demand are common. Beyond semiconductor components, we also provide electronic instruments and software solutions, serving as a total solution provider.

PROJECTS KSS SONAR System KDX-III SONAR System Wire-Guided Heavyweight Torpedo Harbor Underwater Surveillance System (HUSS) ITEMS Transceiver cabinet assembly

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

- Installed on the fuselage or tail to provide flash lighting in a location that does not impede the visibility of position lights - The reflector rotates in an arc. - Flash Rate : 40 to 100 times per minute [cycle] - Effective Intensity : FAA FAR 29.1401 - SAE ARP 5825A

The new TAC-450-320/340/360 inertial measurement unit (IMU) is a dependable, tactical-grade, non-ITAR inertial system that’s also affordable. It features EMCORE’s exclusive photonic integrated chip (PIC) technology for robust performance and survivability and offers inertial-grade MEMS accelerometers for outstanding FOG-based inertial performance as affordable as MEMS alternatives. The TAC-450-320/340/360 IMU is ideal for autonomous and unmanned commercial and defense applications, mobile mapping and surveying systems, targeting and pointing systems, and guidance and positioning. Highlights Compact and lightweight with high-performance Offered with 16g inertial-grade MEMS accelerometer Robust performance with high bandwidth Technology Details Photonic Integrated Chip Technology EMCORE’s photonic integrated chip (PIC) technology reimagines FOG technology by replacing individual fiber components with an innovative integrated planar optic chip. This results in a FOG with PIC Inside™ that’s reliable and robust. With three of these integrated photonic gyros at its core, the TAC-450-320/340/360 IMU provides the safe, accurate performance autonomous platforms demand. State-of-the-art Electronics EMCORE’s Dual Core DSP electronics with ARM processor require less power for extended product life and offer higher speed with integrated multi-channel processing. Low-loss optical circuits use less light for greater efficiency. Feature Options Developer’s Kit for Rapid Integration The FOG/IMU Developer’s Kit includes easy-to-use software that accelerates your IMU and FOG integration, development, and interface efforts.

Every feature designed with transparency and openness in mind. Access enterprise-grade quantum computing with the tools you need to innovate.

Our firm offers end-to-end GaN production capabilities, including fabrication, packaging, test, and failure analysis to meet custom requirements. To enable customer designs, a process design kit (PDK) is available with a design manual, sample layouts, and a non-linear device model. Options available include fabrication of customer-designed wafers (“PDK foundry service”) or custom design by TransEON and fabrication according to customer specs (“NRE foundry service”). For either option, volume levels available include pilot/engineering runs, multi-project wafers (MPWs), or full production runs.

EMCORE’s exclusive photonic integrated chip (PIC) technology delivers improved reliability and repeatability. The precision non-ITAR GEO-FOG 3D Dual features two GNSS antennas on a fixed PTK baseline to offer increased heading, pitch, and roll accuracy for static and dynamic applications where a single antenna system can be problematic. This dual antenna INS is the best choice for systems requiring heading at start-up or in low dynamic conditions. Highlights Data rate 10x faster than other available systems Cutting-edge sensor fusion for dependable, precise navigation in a full array of applications and conditions Six degrees of freedom (DoF) IMU with integrated gyros and accelerometers Technology Details Photonic Integrated Chip Technology EMCORE’s new photonic integrated chip (PIC) technology reimagines FOG technology by replacing individual fiber components with an innovative integrated planar optic chip. This results in a FOG with PIC Inside™ that’s even more reliable and delivers superior repeatability unit-to-unit. With three of these integrated photonic gyros at its core, the P-1750 IMU enables the GEO-FOG to provide the safe, accurate performance autonomous platforms demand. Learn More DSP Technology EMCORE’s DSP electronics improve FOG performance in critical areas such as scale factor and bias vs. temperature, scale factor linearity, and maximum input rate. EMCORE’s exclusive DSP design overcomes the limitations of analog signal processing, eliminating temperature-sensitive drift and rotation errors. GEO•FOG Manager The GEO•FOG Manager is ideal when integrating EMCORE’s GEO•FOG 3D and GEO•FOG 3D Dual INS. Learn More Developer’s Kit for Rapid Integration The KVH FOG/IMU Developer’s Kit includes easy-to-use software to accelerate your IMU and FOG integration, development, and interface efforts.