It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

1) Fabrication - possible Dismension : ~ D 1200 mm - Surface Errors PV < 79 nm RMS < 12 nm Roughness < 2 nm(Typical < 1nm) 2) Lightweight - lightweight Ratio : up to 82.5 % - Rib Thickness : ~ 2 mm - Face Sheet : ~ 7 mm - Lightweight Design & Fabrication

- Dimensions (L x W x H): 40 x 90 x 35 mm (receiver + antenna array) - Weight: 120g (receiver + antenna array) - Power Consumption: 3W - Constellations: GPS, Galileo, GLONASS, BeiDou, NavIC - Frequencies: L1/L5 or L1/L2 - Interference Resistance: Single jammer up to 90 dB (J/S)

Developed by MPS Microsystems, the voice-coil nano-positioner unites a Lorentz-force motor, flexure guidance and on-board electronics inside a 65 × 60 × 38 mm envelope. Standard travel is 2.88 mm, extendable to 7 mm with the same coil, suiting microscope objectives, small mirrors and sensors that demand friction-free motion. Bidirectional repeatability stays within ±1 µm over a 360 µm stroke and ±2.5 µm across the full stroke. We can tailor mounting plates, objective clamps and cable exits to suit your specific requirements, ensuring that this voice-voil actuator can be integrated seamlessly into your system.

CBOL Corporation is pleased to highlight our role as the producer of the H-250/U handset and our role in the supply chain, as we actively contribute to fulfilling the needs of a respected U.S. military OEM through having passed its rigorous qualification requirements. We take great pride in our ability to meet our valued partners' evolving demands in ensuring national security and abroad.

The EMC-102 EDECU is configured as a common supervisory engine control for both T700-GE-701C/D and T700- GE-401C applications. Slated for use by the Army on current fielded models of Black Hawk helicopters, the control is configured with modern electronics, allowing for a more reliable alternative to the present Black Hawk control. The control unit is also compatible with the AH-64 Apache. The control is qualified to the latest Army requirements for superior operability in adverse environments.

In this video, you will learn about the capabilities and performance benefits of our 5G mmWave semiconductor test system, the GENASYS Semi TS-900e-5G. GENASY...

- Reduced weight and manufacturing cost by more than 30% compared to conventional metallic propellant tanks - Designed and qualified to according KARI requirements - Proof & burst pressure application - Cyclic pressure(MEOP, Max. Enveloped Operating Pressure) application, more than 40 cycles