Various line up, high torque frameless motor capable of precise speed and position control. Application areas are Collaborative robots, Dog Horse robots.

Threaded bushing enables localized reinforcement of and attachment to panel structure. Supplied with disposable installation fixture. 1.25" Flange Diameter. SIZES: Imperial fine thread sizes from 10-32 (.190"-32) to 3/8-24 (.375"-24), Imperial coarse thread sizes from 8-32 (.164"-32) to 3/8-16 (.375"-16), and metric thread sizes from M5 to M8. 1.25" Flange Diameter. Grip lengths from 0.25" to 1.50". MATERIALS: Aluminum, 300 Series Stainless Steel, A-286 Stainless Steel, 316 Stainless Steel, and Titanium. Optional epoxy primer. FEATURES: Standard 1.25" diameter flange, 0.75" x 1.25" trimmed flange optional.

The SC-SSGMRTM, a Seedcore Co., Ltd representative product, is a backplane transmission module that performs the I/O function of the SSGM(Synchronous Signal Generation Module). When the SSGM(Synchronous Signal Generation Module) board is plugged into the motherboard(Backplane) in front of the Chassis, you can extend the I/O function of the board by plugging the SC-SSGMRTM board into the back of the Backplane. Three 37-pin Micro D-sub ports are used to send synchronization signals generated by SC-SSGM to the outside or to receive external synchronization signals, Three separate MMCX output ports are prepared to support test equipment such as oscilloscopes, and you can convert them to various signals and output them.

항공 엔진용 테스트셀·시험장비 및 데이터 솔루션을 설계·구축하는 세계적 기업으로, 상업·국방·MRO 고객의 터보팬/터보샤프트/APU 등 다양한 엔진 시험 요구를 지원합니다.

ts advanced integrated optics and closed-loop Field Programmable Gate Array (FPGA) electronics deliver much higher accuracy, lower noise and greater efficiency than competing technologies. In addition, the EG-1300 can be calibrated internally for better thermal effect and has both digital and analog outputs, along with separation of the electronics from the FOG’s sensing coil assembly to accommodate the widest variety of installation parameters. Features Fully-integrated optics and electronics Advanced optics and FPGA electronics for higher accuracy, lower noise and greater efficiency Precise navigation (1 mile/hour without GPS) Fast, precise gyrocompassing to 1 milliradian Bandwidth to 500 Hz Separate electronics and sensor modules More economical than competing systems Applications Navigational grade applications Unmanned aerial vehicle (UAV) guidance Missile guidance Aeronautics and aviation Robotics

This Control Actuation System (CAS) is a guidance system for unmanned flying objects. It consists of three MPS fin actuators that each independently position an aerodynamic fin. The maximum angle of incidence is ±8°, which allows the device to carry out highly precise dynamic manoeuvres. The miniature fin actuators that make up this Control Actuation System are manufactured by MPS Microsystems and were designed based on customer specifications. Designed to guide a very small object and disposing of an extremely limited space, these fin actuators meet strict requirements in terms of performance, weight - less than 100 g - and dimensions. To reduce the length of this actuator, MPS Microsystems used part of the screw length as the motor axis. This screw is equipped with a very compact 4-point contact bearing that simultaneously absorbs axial and radial loads. The angular play on the aileron axis is less than 0.1° rms. This actuator meets the storage and vibration requirements of military equipment.

Woori DS Co., Ltd. has developed firmware for a cooling and heating air conditioning system that performs all controls, fault diagnosis and communication for heating and cooling control and positive pressure control inside an armored vehicle, and developed an inverter control device capable of controlling communication with the armored vehicle body system and monitoring error situations. We are developing products based on the best technology and competitiveness to satisfy customer requirements for electrical equipment required for armored vehicles. In addition, we have developed an air conditioning system blower durability test device that can test the durability of air conditioning blowers, and we have secured test and evaluation technology for blower durability by checking blower errors and performing cycle management. By continuously securing innovative technologies in the defense industry, we are expanding our electronic device development business to deliver new value and impress customers with the highest quality and trust from product design, development, and mass production.