It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

Our ultra-premium DB961WP answers the call for increased durability, providing the dependability and reliability industrial applications demand. Coupling massive torque and high speed with its wide voltage range and high resolution/low deadband circuitry, this hardened steel gear, fully programmable actuator delivers the ultimate in high performance. #UAV #UAS #UGV #UUV #USV

The Fibre Channel D-sub connector series features a multi-finger ground spring fixed around the shell provides a multi-point contact engagement that affords superior EMI shielding. The end result is extremely low contact resistance when measured from the contact outer body to the connector flange. The Fibre Channel D-Sub series also delivers superior performance ensuring minimal RF noise and high durability up to 1,000 mating cycles, while meeting and surpassing all requirements of MIL-STD-202 for shock and vibration. Offered with 150 Ohm quadrax contacts, the connectors are available with 2, 4, 6 or 8 way insert arrangements. Additionally, D-Sub connectors feature ease of assembly, and a robust and comprehensive training package. To ensure that the correct high speed connectors are mated to address specific wiring requirements and keying functions, a keyed jack post option has been incorporated into the design. The six-positioned post allows for 36 possible keying combinations assuring that the correct Fibre Channel D-Sub plug is mated to the correct high speed receptacle. Non-keyed jack post versions are available as well. Fibre Channel D-Sub connectors feature size 3 quadrax contacts which are 30% larger than the size 9 configuration utilized in the 100 Ohm quadrax, ensuring a matched impedance signal throughout the contact mated pair at 150 Ohm differential impedance. These features ensure that Smiths Interconnect's Fibre Channel D-Sub connectors deliver the critical edge customers require.

With more than 3,000 EO/IR sensors on order or delivered, the Star SAFIRE® series provides the longest range performance in its class.

A ground control system that establishes unmanned aerial vehicle missions, controls aircraft and mission equipment, reads image information, and transmits it to higher-level units.

REP series is easy to use for quick mating. The REP panel and cable connectors are a highly cost-effective interconnect system, which solves the constant need for simple and reliable connector solutions in rail applications. A full plastic solution offered in either wire attachment or PCB mounting options to provide rapid assembly installation without requiring additional mounting hardware. Cable receptacle connectors are available to mate with the cable plug connectors for cable-to- cable solutions when needed. The series is qualified to French and European rail standards. The connectors are available as one overmolded plastic part to save assembly time.

Servo control is performed to remotely drive the armament device of the unmanned search vehicle and shoot at a moving target. - PMSM 4-axis servo control - Built-in regeneration function - Self-inspection and protection function