It is a hybrid-powered(Engine + Generator) multicopter system that significantly overcomes the limitations of short flight times typically associated with battery-powered drones. It can carry up to 10 kg of mission equipment and perform operations for up to 2 hours, with the capability to autonomously land on moving vehicles and naval vessels. Its versatility is further enhanced through the development of various mission equipment, making it suitable for multipurpose applications.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).

• Contacts • Backshells / protective caps • Solders sleeves / splices • In-line junctions • Identification labels • Wire terminals

The aerospace industry has brought one of humanity's oldest dreams to life, a dream that seemed out of reach for so long : the ability to fly, to travel among the stars. Symbolizing freedom, discovery and travel, airplanes bring people together and foster cultural exchange.

SAIT CIRUS has been fortunate to receive generous funding from the Canada Foundation for Innovation (CFI), Natural Sciences and Engineering Research Council of Canada (NSERC), and Prairies Canada to support the development of our research centre and supporting applied research projects. Our research centre features a diverse and advanced fleet of remotely piloted aircraft, sensors, survey equipment, data processing and modeling software, and hardware. Some of our remotely piloted systems are the only ones in North America, making CIRUS a leading research centre on the continent.

[Infrastructure long products] For the cutting of high-performance materials and titanium alloys, the Service Center Switzerland has 9 powerful circular and band saw machines for precise cuts up to a diameter of 350 mm. BIBUS METALS AG has had experience in cutting special grades since the company was founded in 1979. - Series and individual cuts of all available materials in the shortest possible time - Blanks for sample material testing - Deburring of bar blanks - Marking according to customer instructions - Re-stamping certificate by SVTI (Swiss Association for Technical Inspection) available on request - Chamfering and pointing of bars [Infrastructure flat products] The BIBUS METALS Group has machining facilities at several locations in order to implement professional processing of customer requirements. We use specialist sheet/plate shears for high-performance materials and titanium alloys up to a sheet thickness of 12 mm. In addition, the group has one of the largest fully automatic plate saws in Europe. The Behringer type LPS 25-125-6A saw can cut titanium plates up to a size of 2000 x 6000 mm and a thickness of 150 mm according to the customer's requirements. Waterjet cutting is carried out with our own machines or in cooperation with selected partner companies. - Series and individual cuts of all available materials in the shortest possible time - Blanks for sample material testing - Marking according to customer instructions - Re-stamping certificate by SVTI (Swiss Association for Technical Inspection) available on request - Shearing up to 12 mm thick - Sawn for panels up to 150 mm thickness with tolerances of -0/+3 mm - Circles/rings or any shapes according to drawings will be water jet cut or precision water jet cut