Patrol Killer Guided Electro Optic Target System

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. Linear Acceleration Compensation Certus Mini uses an innovative algorithm to compensate for linear accelerations. This allows Certus Mini to maintain accurate roll and pitch through short term linear accelerations that typically cause significant errors in competitors systems. For long term linear accelerations Certus Mini supports the addition of an external GNSS receiver for full acceleration compensation. Extensive Interoperability Certus Mini seamlessly communicates with a wide range of industry standard protocols including NMEA 0183 and CANOpen making it easy to integrate into existing systems. Certus Mini effortlessly interfaces with ROS 1, ROS 2, and Ardupilot, streamlining your development processes for maximum efficiency and effectiveness.

Mil-COTS Isolated DC-DC converters brings SynQor’s field proven high-efficiency synchronous rectifier technology to the Military/Aerospace industry. These “off-the-shelf” converters are compatible with the industry standard format, operate at a fixed frequency, and follow conservative component derating guidelines. MilQor products are designed and manufactured to comply with a wide range of military standards.

The Haigh-Farr Wraparound™ is a self-contained omnidirectional antenna for cylindrical or conical shaped bodies. A single point feed is used and no external splitters, combiners or cable harnesses are required for installation. The antenna is conformal, and may be mounted flush, or on the exterior of the vehicle. Designs are available from 300 MHz to 13 GHz with typical applications including Flight Termination, GPS, Telemetry, Data Links and Transponder. Multiple antenna elements may be combined within the same physical Wraparound™, providing multi- band capability in a single, compact package. Wraparound™ antennas have been flown on vehicles from subsurface sea to space, including high-mach kinetic kill weapons, high-G projectiles and re-entry vehicles. The Wraparound™ has been qualified for use on several high performance vehicles flown on test and launch ranges throughout the United States and Europe. For high aero-heating applications an ablative heat shield may be added to the antenna for additional thermal protection.

The ENS4000(Sub-6 5G Outdoor base station) is designed for outdoor services in the n79 (4.7GHz) band, providing coverage on the kilometer scale and enabling seamless private 5G service even in outdoor environments.

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.

Safran Engineering Services offer includes EWIS technology design and certification, electrical requirements management, electrical systems architecture, definition and wiring architecture, components definition (BOM), electrical wire harness assembly, installation design, electrical load analysis, 3D modeling / 2D drawing creation, manufacturing tools (Formboard), work Instruction development and wire harness installation design.

Amphenol RF is the world's largest manufacturer of coaxial connectors used in radio frequency, microwave, and data transmission system applications. Headquartered in Danbury, Connecticut, USA, Amphenol RF has global sales, marketing, and manufacturing facilities in North America, Asia, and Europe. Its connectors, adapters, cable assemblies, and other RF and microwave solutions are widely used in a wide range of industries and applications, including automotive, broadband broadcasting, instrumentation, medical, and defense wireless equipment. Amphenol RF's industry-leading manufacturing technology and process control enable it to produce high-quality coaxial connectors and cable assemblies at high volumes.