Haynes International Inc. is a manufacturer of metal alloys employing more than 1,070 employees worldwide with sales of $434.4 million in 2007 with 8 plants ...

Small wind power systems and component components Durability technologies: Composites - nacelle, blades, corrosion protection Stability technology: and wind speed control (electrical) + tail folding (mechanical) High-efficiency system: Direct-drive PMSG - slotless, blades, coefficient of power (Cp): 0.429 MPPT (Maximum Power Point Tracker) : Maximum power following control Web monitoring: Real-time monitoring Easy to maintain and install Quality Assurance: More than 3 years System certification: New and renewable energy facility certification, new product (NEP), excellent product designation by the Public Procurement Service - Korea's first Element parts certification: generator, inverter-CE, blade static load test, demonstration test completed Annual average wind speed of 4.5m/s or more

1) Fabrication - possible Dismension : ~ D 1200 mm - Surface Errors PV < 79 nm RMS < 12 nm Roughness < 2 nm(Typical < 1nm) 2) Lightweight - lightweight Ratio : up to 82.5 % - Rib Thickness : ~ 2 mm - Face Sheet : ~ 7 mm - Lightweight Design & Fabrication

i3system’s line scanning X-ray detector platform, XID-C15DP/XID-C24DC, is a high performance and cost effective solution for dental panoramic, cephalometric applications. i3system’s direct type sensor ensures the most sharp images among the current products in the market. XID series is designed for compact size and easy installation. High DQE(Direct Quant㎛ Efficiency) enables high performance at lower dose of X-ray. Introduction Indirect type X-ray detector uses the scintillator and the photo-diode(CCD or CMOS sensor) for conversion of the X-ray into the light and for taking images espectively. But the light scatters and goes extinct during it passes through the scintillator and reaches to the CCD or CMOS sensor. As a result, it is inevitable to get blurred image. In the mean time, XID C15DP, direct type detector, converts X-rays into electronic signals directly without conversion process of light. Because X-ray is not converted into light, it provides much sharper images than indirect type detector. XID C15DP is designed to compact for easy installation. It provides Gigabit Ethernet port on the detector for easy configuration. Instead of Gigabit Ethernet, camera link or optical interface can be provided according to requirements of users.

RF Systems designs and manufactures antennas for UAVs, guided missile seekers, and satellite systems. Through proprietary Dip Brazing process, we achieve high structural precision and RF reliability in every antenna. 1. Guided Missile Seeker Antenna 2. UAV Slot Array Antenna 3. Satellite Communication Antenna 4. Satellite Lightweight SAR Antenna 5. Satellite SAR Feed

Hydraulic top bracing is an attenuation device installed between the main engine and the hull of the ship to reduce thermal expansion and vibration from the main engine to natural frequencies. The operating principle is an automatic control operating system through in/out and on/off the operating range of the hydraulic top bracing according to the rpm of the main engine. The number of hydraulic cylinders per engine is typically 2, 4, 6 depending on the type of engine, up to 8 are installed if necessary, and 1~2 of control panels are installed.

It is commonly used in industrial and other devices to generate triggers ranging from one to several thousand FPS, ensuring precise timing synchronization with various devices. Periodic Mode: Continuously generates trigger signals after configuration. Burst Mode: Generates a single trigger signal upon receiving the best command via serial communication. *** Product Expansion and Usage ***  Four Operating Modes  Periodic mode: Generates a single-cycle signal based on the configured frequency and duty ratio.  Burst mode: Generates a single-cycle signal synchronized with a software trigger.  External trigger mode: Generates a single-cycle signal synchronized with an external trigger.  External trigger bypass mode: Distributes signals triggered externally.  Connect the trigger output signals from a Master Trigger Generator to a Slave Trigger Generator (as shown below).  By connecting one of the Master TG’s Trigger Outputs (1 to 16) to the Slave TG’s External Trigger Input: Outputs 1 to 15 of the Master TG remain unchanged. Outputs 16 to 31 of the Slave TG will mirror the Master TG’s Trigger Output. (Note: Each trigger signal passing through a TG experiences a delay of ten ns. However, since trigger outputs operate in the range of tens to thousands of Hz, users will not notice the delay).  Example with 17 TGen-16C units: Produces up to 256 Trigger Output Channels (16 × 16).