Signaty X IR Helmet Strobe is a next‑generation, domestically developed IFF LED device. It features IR plus RGBW color LEDs (red, green, blue, white), all housed under a high‑strength polycarbonate dome. It supports multi‑wireless synchronization via short‑range communication, GPS/RTC, and mesh relay—enabling simultaneous use of RGB LED + IR or RGB LED + white LED, with up to 42 pattern synchronizations (expandable to 252) using 256‑bit encrypted data. Runtime reaches up to 130 hours (LED 130 h / IR 125 h) on a single AA battery. Built to MIL‑STD‑810G and KC standards, it ensures drop, dust, sand, immersion, and temperature resistance. Manufactured in Korea with domestic service support.

Key RADAR in counter-fire warfare to defeat enemy artillery by reversely tracing the trajectory of ballistic missile. Design and Manufacture - Environmental Control Unit - Driving unit - Generator - TR module rack & Antenna Case

FIRSTEC is providing key components of guided weapon, such as Actuation System, Gudiance Control Unit, Fire Control Unit, and wire harness, to complete systems such as Hyunmoo, Raybolt(Hyungung), Bigung(Poniard), M-SAM II(Cheongung II), L-SAM etc. applying them to each business.

1) Fabrication - possible Dismension : ~ D 1200 mm - Surface Errors PV < 79 nm RMS < 12 nm Roughness < 2 nm(Typical < 1nm) 2) Lightweight - lightweight Ratio : up to 82.5 % - Rib Thickness : ~ 2 mm - Face Sheet : ~ 7 mm - Lightweight Design & Fabrication

This is the UAV launchers capable of launching the fixed-wing UAVs even on mountainous terrain, field, ships without sufficient runways to take off. It is designed to be the most powerful and easy to operate to take off the fixed-wing type UAVs of various specifications(Take-off weight, Take-off speed, and allowable G-force) into the air. It provides an interface that standardizes the shuttle for any type of unmanned aviation vehicle, and is easy to mount and to avoid take-off interference. A specially designed and manufactured hydraulic actuator is used to fully cope with the take-off weight of the aircraft, and a proprietary accumulator to allow a wide range of launch speed control. And multiple pulleys are equipped to ensure acceleration performance.

Decontaminated and / or sterilized gloves PIERCAN has offered its customers decontaminated and/or sterilised gloves. This service is intended in particular for pharmacy environments (pharmaceutical laboratories, hospitals etc.) but it may also be for industries in which an extremely high level of cleanliness is now absolutely vital (space, military, research etc.).

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. L1/L5 Multi Constellation RTK GNSS The Certus Mini N supports L1/L5 dual frequencies, and GPS, GLONASS, Galileo, BeiDou and NavIC constellations. Access to multiple constellations and frequencies provides enhanced accuracy, availability and performance even in difficult environments such as multi-storey urban canyons. The GNSS receiver has 10 mm position accuracy with real-time RTK or post-processed PPK. Extensive Interoperability Certus Mini seamlessly communicates with a wide range of industry standard protocols including NMEA 0183 and CANOpen making it easy to integrate into existing systems. Certus Mini effortlessly interfaces with ROS 1, ROS 2, and Ardupilot, streamlining your development processes for maximum efficiency and effectiveness.

High productivity • The nodding head type spindle maximizes productivity and efficiency during multi-face and 5-axis simultaneous machining operations. High rigidity • Dual ball screws deliver improved stability and responsiveness for heavy-duty cutting. Easy chip disposal • The machines’ central chip removal system improves operational efficiencies.