This solution leverages LLM-based data interpretation technology to detect process anomalies in advance, providing alerts and countermeasures before defects occur, thereby ensuring sufficient response time. It also analyzes issues such as positional misalignment or print degradation patterns during the process, matches them with various event timelines, identifies the root causes of defects, and delivers the findings in the form of analytical reports

- To check and verify the RWR system on the aircraft and radiate threat signals to RWR antenna through couplers. - Radiate threat signals to jammer system.

The SBC6511 Rugged Single Board Computer(SBC) from Abaco Systems features the new high performance, highly integrated Intel® Xeon® E processor (‘Coffee Lake Refresh’). Powered by Intel® Xeon® W processors, offering robust computational power. • Supports up to 64 GB DDR4 SDRAM with ECC and up to 256 GB (or in some variants up to 480 GB) NVMe SSD storage • Offers high-throughput networking: Dual 40 GbE data-plane (KR4 “fat pipes”) • Features the Xilinx® Zynq® UltraScale+™ MPSoC FPGA (ZU7EG) for enhanced security

[Cutting by water jet] Micro water jet cutting: The micro water jet enables a refined process to be carried out in precision cutting. This high-precision technology reduces the jet diameter by a factor of 5 and makes water jet cutting more precise by a factor of 10. The micro water jet achieves a cutting accuracy of +/- 0.01 mm and a positioning accuracy of ±0.005 mm. The proven advantages of the cold cutting process remain unchanged. In the pure water process, the cutting width was reduced to 0.2 mm in the abrasive process for hard materials such as nickel-based alloys and titanium. The new technology controls the cutting process and manipulates the cutting path depending on the contour and speed enabling a highly precise cut. Standard waterjet cutting: Water jet cutting is highly efficient and at the same time less severe than other cutting techniques. Low process forces and thermal loads prevent bending or melting. We can cut filigree delicate contours from practically all nickel alloys and titanium alloys. Using our standard process we can cut a range of shapes and dimensions according to customer requirements and drawings and achieve tolerances of +/- 0.1 mm or +/- 0.2 mm.

EO/IR Payload System EOTS (Electro-Optical Tracking System) is an electronic optical image tracking device that identifies danger and emergency situations on the battlefield, monitors and tracks tragets, and calculates their coordinates, and is an essential equipment for drones that can be used in both military and private sectors. M1 and M2 were developed to use a common mount that connects to the drone by keeping the size of the gimbal assembly the same at 4 inches. M1 can be recognized at a maximum of 0.2km for humans during the day and at night, and M2, which operates in adverse conditions at night, can be recognized at up to 1.0km for tanks in the form of IR continuous zoom.

This miniaturized system allows, depending on the desired configuration, to move very precisely between 1 and 3 sets of lenses over a stroke of several centimeters. The design has been optimized to ensure perfect alignment of the lenses and to minimize their tilt throughout the movement. This optomechanical system mainly consists of high-precision standard MPS and FAULHABER modules, such as brushless or stepper motors, ground ball screws with double nuts and linear ball bearings. It is particularly recommended for focusing a laser over a long distance, for example for the guidance of unmanned flying objects or for communication between flying objects. The number of lens sets, lens size and stroke can be configured at will.

Investigate the smallest of features with spatial resolution down to 600 nm – A state-of-the-art nano-focus x-ray source, precision stages, and high-quality detectors work together to deliver sub-micron resolution imaging. Perform true 4D imaging with Dynamic CT – High temporal resolution, continuous and uninterrupted scanning, and specialized 4D software tools bring synchrotron-like capabilities to the lab. Implement 3D in situ experiments – continuous sample rotation and scanning enable uninterrupted in situ experiments. Dedicated “no-cable-wrap” interfaces simplify experiment set-up. Accommodate a broad range of samples – UniTOM HR’s high power source (50W), multiple detector options (up to 3) and heavy load stage (45 kg) accommodates samples up to 500 mm diameter X 700 mm high. Maximize system utilization and throughput – A fast frame rate detector and a high flux x-ray source combine for high temporal resolution tomography giving you the ability to scan more samples and accommodate more users.