The SCXMC-HDLC card operates through the XMC interface of the SBC and provides real-time communication for control and status data based on synchronization signals. It supports serial communication via the SBCRTM’s Micro D-sub 37-pin connector using a standard D-sub 9-pin interface, allowing long-distance transmission through LVDS signaling. With four transmit/receive channels, it achieves 1–8 Mbps per channel and delivers low-latency performance of less than 40 µs for real-time operations. A device driver program is required for operation, and the Linux driver can be downloaded from Seedcore’s product page. Drivers for other operating systems can be developed upon request. This module is deployed in the L-SAM multi-function radar system, enabling fast and reliable control data communication across mission-critical components.

Our MDB1200WP industrial actuator offers a contactless magnetic encoder, brushless motor and IP67-certified water & dust-proof protection, making it suitable for many demanding industrial applications. This 30mm powerhouse delivers over 1500 oz-inches of torque at 7.4V and features an aluminum alloy case to dissipate heat, two ball bearings and five hardened steel gears, and PWM control protocol. Program numerous parameters to optimize the installation and performance for your industrial applications. #UAV #UAS #UGV #UUV #USV

The engine is suitable for MALE AUVs. Available in pusher and tractor configurations. Digital interface for control and monitoring. Stable operation at high altitudes and high temperatures. Ability to run at cold temperatures below -30°C without preheating.

High Power Polarizing Beamsplitter Cube coatings are deposited on the hypotenuse of right angle prisms that are optically contacted. They are designed to separate an incident beam into its S and P polarization components with an average extinction ratio (TP/TS) in excess of 500 : 1. The incident energy is split into two orthogonally polarized beams that emerge at 90。with respect to each other. These coatings were developed specifically for use in high power pulsed and CW laser applications.

ElectroAir’s mobile APA-65 -series combined units consist of frequency converter units (AC rated output power up to 45 kVA) and rectifier units (DC continuous current up to 800A). These units are intended for the ground servicing of all aircraft types with a frequency of 400Hz and voltage 115/200 V and to power on-board electrical equipment and launch aircraft/ helicopters with a voltage of 28.5 VDC. APA-65 series is designed to eliminate CO2 emissions with its unique technical characteristics. Diesel hybrid unit and battery driven unit - unit can perform the complete service of aircraft at remote parking places with diesel engine / through batteries and it is also capable to operate from the 50/60Hz, 400V, 3 phase main power supply grid as any electrical GPU, without fuel consumption and with zero operating emissions. The range of different APA configurations with no emissions allow for safer, cleaner and more practical operational conditions for operators and personnel at the location. These units are very compact in size and weight.

The System 100 Single Tube Mast is a lightweight, high-strength solution for fast, flexible deployments in military, emergency response, and expeditionary communications operations. Its single-tube design enables controlled, safe extension and retraction to the desired height, streamlining setup and pack-down in time-sensitive scenarios. Engineered for both static and mobile applications, the mast can be mounted directly on the ground, vehicle, or trailer, providing a stable foundation across varied terrains. When not in use, it can be compactly stored to reduce bulk and simplify transport. Combining portability, durability, and operational agility, the System 100 ensures reliable performance in demanding field conditions.

Ultra-High Accuracy MEMS Motus features some of the highest accuracy MEMS accelerometers and gyroscopes currently available. Motus’s inertial performance exceeds some FOG IMUs and is up to 100x smaller and 10x cheaper. Motus is put through Advanced Navigation’s intensive calibration process to provide consistently accurate data over an extended temperature range of -40°C to 85°C. Miniature Package Never before has such high inertial performance been available in such a small package. Motus consumes just over 1 cubic inch in volume and weighs only 26 grams. This makes it ideal for weight and size sensitive applications. Motus is available in an OEM package suitable for integration into larger products or an enclosed package for external and standalone use. Advanced Signal Processing Motus samples its sensors synchronously at 1000Hz through six individual 24-bit differential ADCs which minimizes noise as well as providing optimal thermal calibration and performance characteristics. 14 separate heavily filtered regulated power supplies ensure that each sensor and ADC is operating off the cleanest possible power supply. Reliability Motus has been designed from the ground up for mission critical control applications where reliability is very important. It is built on top of a safety oriented real time operating system and all software is designed and tested to safety standards with fault tolerance in mind. The hardware is designed and manufactured to mil standards. High Update Rate Motus outputs temperature calibrated sensor data at 1000Hz as well as filtered attitude at the same rate. This allows for control of dynamically unstable platforms.