A comprehensive line of products in C, X, Ku, Ka and Q-band for SATCOM and 5G&6G are available as off-the-shelf items or custom-made design upon request. These products are specialized in various types of mobility environment including airborne application. We serve the customers in more than 20 countries with fully field proven products. The new era of wireless communication requires a converged solution of SATCOM and 5G&6G in the aspects of technologies and services. XMW is preparing for the new era with the solutions inherited from SATCOM and 5G&6G business for more than a decade.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Amphenol Aerospace designs and manufactures QPL Mil-spec and custom circular and rectangular electrical and electronic connectors for the military and aerospace industries. We also specialize in designing and building high-speed cable assemblies, media converters and Ethernet switches, fiber optic connectors and cable assemblies, high power and high voltage connectors, EMI/EMP filter connectors, hermetically sealed connectors, and a variety of special applications connectors and custom interconnect systems.

< Frequency Range > ● LB-400: 400 ~ 460MHz ● LB-900: 800~928MHz ● MB-1500: 1300~1500MHz ● MB-2400: 2400 ~ 2500MHz ● HB-5.2: 5150 ~ 5250MHz ● HB-5.8: 5725 ~ 5875MHz < TX path output Power (at antenna port) > ● Normal mode: 35dBm [min] ● On each antenna port 2x 35dBm ● Interference mode: 40dBm [min] < TX path maximum Input Power > ● +20 dBm < RX path Gain > ● 25dB typ. < RX path Noise figure > ● Low bands: 3dB max. ● High bands 3.5dB max. < RX path IIP3 > ● -10dBm typ. < RX IP1dB compression point > ● 15dBm typ. < Power Supply > ● +24V ± 1 Vdc

AI Navigation Algorithm Certus features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. It was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS Certus contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Dual Antenna RTK GNSS Certus contains a dual frequency RTK GNSS receiver that provides up to 1 cm accuracy positioning and supports all of the current and future satellite navigation systems, including GPS, GLONASS, GALILEO, BeiDou and QZSS. Dual antenna heading provides high accuracy heading that is not impacted by magnetic interference and has no motion requirements. Time Synchronization Certus contains a GNSS disciplined oscillator that can act as the primary time source within a distributed time system, enabling access to ultra-accurate system time using PTP or NTP network time sync. Certus also has a high-accuracy 1PPS and frequency output. Multi-Protocol Support Certus features multiple interfaces including Ethernet, CAN, RS232, RS422 and GPIOs. Certus supports all the industry standard protocols including NMEA 0183, NMEA 2000, TSS, PASHR, Simrad as well as a wide variety of proprietary protocols. It features a rich web UI and 256GB of internal logging.

Large Area Display Head Unit is included in avionics equipments used in the cockpit of an aircraft. Its wide screen vision development implements Full Glass Cockpit in aircraft. It also provides processing with more efficient yet less complicated circumstance with maximum 4 external input video signals Options that can be provided are - 20"x8" LCD Glass, LCD Module and Entire LAD system unit

From precise control of various optical components(laser/detector/amplifier) & laser beam alignment(QD/FSM), a data rate of 10G can be achieved over distances of several thousand kilometers.

The Aerospace & Defense Team's Business Service Providers (BSP) Directory is designed to help U.S. aerospace & defense companies identify professional service providers to assist them in the assessment, completion, and/or financing of an export transaction.