STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Every year, we celebrate World Space Week in October to honor scientists' contributions to space research and inspire the next generation of innovators. Honeywell has been a part of every NASA human space mission since the late 1950s, when our flight-control systems were installed on the X-15 Rocket Plane (shown above in a photo of Neil Armstrong after a research flight in November 1959).

Liquid Measurement Systems (LMS) provides fuel gauging and interface controls for service, maintenance, and flight crew personnel, at the primary refuel point on the aircraft.

External Refuel Preselect Panels can display the quantity of fuel in each tank, calculate the total quantity of fuel onboard, allow service teams to pre-select desired fuel quantity, and display fault codes. LMS’ external refuel preselect panels are compact, lightweight, and rugged systems that can be adapted to a variety of platforms.

암페놀-대신전자정밀(주)는 Amphenol Corporation의 한국 법인으로, 산업용, 군수용, 이동 통신 및 철도 차량용 커넥터를 주력 제품으로 생산하고 국내 시장 뿐만 아니라 수출 및 해외 암페놀 법인의 제품을 한국 시장에도 공급하는 공식 자회사입니다.

Featuring an ultra-compact package of less than 5 cubic inches, the TAC-440 delivers 1°/hour gyro bias with 1 mg accelerometer bias stability and very low 0.05°/√hour angle random walk (ARW) over wide temperature ranges. The breakthrough performance of the TAC-440 IMU is based on a EMCORE’s proven quartz MEMS inertial sensor technology. EMCORE’s quartz technology enables repeatable, high-volume production of precisely machined sensor structures combined with the inherent large signal output and thermal stability of quartz materials. The TAC-440 is a compact IMU constructed with EMCORE’s latest generation quartz gyros, quartz accelerometers, and high-speed signal processing to achieve outstanding precision performance. The TAC-440 IMU is designed for demanding, mission-critical, rugged environments. The solid-state quartz sensors and hermetically sealed IMU construction provide reliable MTBF. Continuous Built-in Test (BIT), configurable communications protocols, electromagnetic interference (EMI) protection make the TAC-440 IMU easy to use in a wide range of higher order integrated system applications.

The SC-SSGMRTM, a Seedcore Co., Ltd representative product, is a backplane transmission module that performs the I/O function of the SSGM(Synchronous Signal Generation Module). When the SSGM(Synchronous Signal Generation Module) board is plugged into the motherboard(Backplane) in front of the Chassis, you can extend the I/O function of the board by plugging the SC-SSGMRTM board into the back of the Backplane. Three 37-pin Micro D-sub ports are used to send synchronization signals generated by SC-SSGM to the outside or to receive external synchronization signals, Three separate MMCX output ports are prepared to support test equipment such as oscilloscopes, and you can convert them to various signals and output them.

KMC Series includes high-density board to board and board to wire interconnect solutions available in multiple configurations from 26 to 162 positions with a 0.5mm contact diameter and is widely used in harsh environments. Space grade/ESA/ESCC qualified are also available.

The versatile and adaptable Challenger 3500 aircraft is the most reliable and best-selling business aircraft in its class, with more than 1,000 delivered in this series. It has the widest cabin in its category, offering ample space for workstations, patient transport and mission equipment.