The IntuVue RDR-7000 is fully automatic and does'nt require active pilot adjustments of tilt and/or gain for operation. Reducing workload, allows pilots to focus on flying the most comfortable and safest route through weather. Engineered to provide far superior reliability, accuracy and durability than legacy magnetron-based radar systems, the RDR-7000 offers customers the flexibility to remotely enable advanced software features to provide them the clearest view of weather conditions around the routes they’re accustomed to flying. Key Honeywell Advantages: Next generation -fully automated, higher resolution weather radar system with airborne ground/sea mapping system Reliable and efficient - solid-state transmitters utilizing pulse compression provide reduced weight and power consumption, advanced coherent processing, and increased reliability Compact and easy to install - RDR-7000 IntuVue radar systems technology integrated into a small, lightweight package Available software upgrades - advanced features can be added at any time, including turbulence detection, advanced mapping, target detection and additional hazard features (lightning and hail detection), and forward looking (predictive) windshear Honeywell's RDR 7000 Radar helps in operational costs savings by reducing the delays & downtime caused due to hailstorm, weather incidents and windshears while optimizing routes to reduce diversions and turnbacks.

- To measure RCS for the aircrafts, warships, helicopters, chaff and etc. - Verify to meet pre-defined RCS specifications on design phase.

- To check and verify the RWR system on the aircraft and radiate threat signals to RWR antenna through couplers. - Radiate threat signals to jammer system.

- RWR receiver inspection and antenna performance measurement - EW receiver inspection - Check the azimuth and signal power of the RWR receiver

R HUGHES' Ca-Zoom PTZ 140 is a Pan-Tilt Zoom Camera inspection equipment equipped with the Ca-Zoom® 6.2 system. This equipment is capable of a total of 432x zoom with 36x optical zoom and 12x digital zoom, increasing inspection efficiency. In addition, two high-performance 35W lights are installed in the light source to enable more smooth inspection. The inspection technology of the PTZ Camera Ca-Zoom® line of products makes them ideal for inspecting large areas that are difficult for humans to access, such as tanks, vessels, pipelines or nuclear power plants.

STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

The Transmit/Receive Module splits 2 transmit input channels into 32 output channels. Each channel delivers an output power of at least 3.2 W with a transmit efficiency of 35.5% or higher. It features independent phase control for each transmit channel. On the receive side, 32 input channels are combined into two output channels. The total receive gain is 34 dB or greater, and each channel supports individual gain and phase control. The noise figure is 3.5 dB or lower per channel. Built-in monitoring functions include internal temperature monitoring and output signal monitoring.

The mighty Hitec SG33BLT Series servo actuators operate on DroneCAN (formerly UAVCAN), CAN 2.0 A/B, RS485, PWM and TTL command protocols, and feature brushless motors, magnetic encoders, and hardened steel gears. They are also environmentally sealed with an IP67 waterproof case rating. The SG33BLT Series was initially developed for the automotive industry requiring minimal support equipment and wiring, saving unnecessary installation complexity, cost and weight. This same functionality is now enjoying widespread adoption of CAN and DroneCAN systems within the UAV environment. With options for both 9~15-volt and 18~32-volt operations, and DB9SUB, Circular, & Gland Cable connectivity, the SG33BLT Actuator Series is sure to have a solution for your needs. #UAV #UAS #UAM #UGV #UUV #USV