STIM300 is a small, tactical grade, low weight, high performance non-GPS aided Inertial Measurement Unit. It contains 3 highly accurate MEMS gyros, 3 high stability accelerometers and 3 inclinometers. The IMU is factory calibrated and compensated over its entire operating temperature range. STIM300 is a cost-effective ITAR free solution for systems that only had FOGs as an alternative when reaching for the performance level of that STIM300 can offer. Each axis is factory calibrated for bias, sensitivity and compensated for temperature effects to provide high-accuracy measurements. The unit runs off a single +5V supply and communicates via a RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sampling frequency, LP filter -3dB frequency and RS422 bit-rate and protocol parameters. For more advanced users, STIM277H may be put in Service Mode. In this mode all the configuration parameters can be temporarily or permanently changed by overwriting the current settings in the flash memory. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail in the status byte.

Wheels used on special vehicles use high-strength forged aluminum wheels because one tire per axle is used for driving on paved roads, unpaved roads, open fields, and sharp turns. Accordingly, our company secures static and dynamic strength considering driving conditions through optimized design technology and maximizes excellent quality and reliability through our own performance tests such as high strength, weight reduction, and shape optimization, and supplies wheels of various specifications for use in special vehicles.

The JW22992 connector was developed for the purpose of high-power transmission with demanding military standards and exhibits IP67-grade water and dust resistance. It is also designed in the range of 40 to 200 amps and is used for high-power military and industrial equipment that requires the highest reliability. Key Features: High Power Transmission, Designed to handle high currents, Robust construction It provides a stable connection with five key grooves and two-line screws.

MPS Microsystems offers a complete range of high precision ball screws for positioning less than 5 µm. Mostly custom-made, these screws ensure smooth and uniform movement resulting from the high precision of their thread, achieved by grinding. Our ball screws are made exclusively of stainless steel and are fitted with double nuts to allow fine adjustment of the axial play. Moreover, an optional ogival thread can provide a higher static and dynamic load capacity. Thanks to a large number of options, we can ensure that the ball screw meets your technical and quality needs. The following parameters can be personalized: lubricant (grease, oil, dry lubrication, no lubrication), customized screw ends, shape and external dimensions of the nut and screw, multiple nuts on the same screw, left-hand thread, thread length, specific axial play, special surface treatment, and more.

AI Navigation Algorithm The Certus Mini range features Advanced Navigation’s revolutionary AI neural network sensor fusion algorithm. The algorithm was designed for control applications and has a high level of health monitoring and instability prevention to ensure stable and reliable data. High-Performance MEMS The Certus Mini range contains high performance MEMS sensors that are put through Advanced Navigation’s intensive 8 hour temperature calibration process. This provides the highest accuracy possible from this sensor class and outputs consistent accuracy over the full temperature range from -40°C to 85°C. Reliability The Certus Mini range has been designed from the ground up for mission-critical control applications where reliability is essential. Built using a safety-oriented real-time operating system, all software is designed and tested to high safety standards with fault-tolerance in mind. The Certus Mini range is designed, manufactured and tested to military standards. L1/L5 Multi Constellation RTK GNSS The Certus Mini D supports L1/L5 dual frequencies, and GPS, GLONASS, Galileo, BeiDou and NavIC constellations. Access to multiple constellations and frequencies provides enhanced accuracy, availability and performance even in difficult environments such as multi-storey urban canyons. The GNSS receiver has 10 mm position accuracy with real-time RTK or post-processed PPK. Dual Antenna Heading The Certus Mini D provides a high accuracy heading solution using two GNSS antennas. The Certus Mini D rapidly and consistently maintains an accurate heading without the need for magnetic calibration and is unaffected by magnetic interference. Additionally, the system can determine heading while stationary. This makes it well-suited to applications where there is limited, or no, positional movement.

Solution Overview EagleEye is a a synthetic data generation & management platform for AI training that integrates image generation, LLMOps, and MLOps. It automates high‑quality dataset generation, labeling, and model validation—and has been certified “military suitable” and delivered first to the ROK Army AI Center. Main Features Image generation with text/image prompts; object/background customization LLMOps: prompt understanding + image–text labeling workflow MLOps: CV model training/validation, dataset versioning, experiment tracking End‑to‑end pipeline from data preprocessing to model deployment Data augmentation and management for scalable, repeatable training Key Advantages Certified “military suitable”; meets defense operational requirements First AI solution supplied to the ROK Army AI Center, proving reliability One‑stop synthetic data + model ops cuts development/validation time Fully in‑house stack enables rapid updates and mission‑tailored customization 2025: First AI product delivered to the ROK Army AI Center for defense AI projects Used to generate and manage high-quality synthetic imagery for military AI model training and validation

Input : 24Vdc Output : 270Vdc N+1 System

Servo control is performed to remotely drive the armament device of the unmanned search vehicle and shoot at a moving target. - PMSM 4-axis servo control - Built-in regeneration function - Self-inspection and protection function